Using advanced features – GoVideo DV1030 User Manual
Page 16
29
VCR
OPERA
TION
28
Press [SETUP] and select
“FUNCTIONS”.
Select “Index Search”.
1
1
■
When you record a program, the VCR places an index mark at the start of the recording. To search for an
index mark:
FUNCTIONS
Auto Play:
ON
Auto TV/VCR:
ON
Index Search
Go-To Search
If you want to scan through a certain number of
index marks, use the number buttons to enter
the number of marks you want to search. Press
CLEAR on the remote to correct an entry.
or
Press REW to search backward or FF to search
forward. The VCR will locate your index mark
and begin playback. If you did not enter a
specific index number, the VCR will locate the
next index mark and begin playback. Press
STOP to stop index searching.
2
2
INDEX SEARCH
Press REW or FF
to begin searching
or
Enter a specific
index number
- -
End:
SETUP
• If two
recordings
overlap, the index
mark for the second
program will be
erased. Therefore,
when you use the
index feature to find
the second program,
the VCR will skip
over it.
• If you record
multiple programs in
one recording
session, the VCR will
only find the index
mark that was
placed on the video
cassette tape when
the recording
session began.
Searching a cassette tape for programs (indexing)
Press [SETUP] and select
“FUNCTIONS”.
Select “Go-To Search”.
1
1
■
You can mark a segment of the video cassette with the tape counter that will help you easily locate the
segment later.
FUNCTIONS
Auto Play:
ON
Auto TV/VCR:
ON
Index Search
Go-To Search
The tape counter is displayed on the screen.
Input the tape counter you want to find and
press REW or FF, the VCR will search for the
time counter you specified.
2
2
GO-TO SEARCH
Current tape counter is
2 : 17 : 18
Press REW or FF
to go to - : - - : 00
Some index
marks that may
be missed by the VCR :
• A mark too close to
your location on the
tape.
• The mark at the
beginning of a
recorded segment of
five minutes or less.
• The first index mark
on the tape when
you start at the
beginning of the
tape.
Searching with the tape counter (Go-To Search)
Using Advanced Features
Using Advanced Features
Auto Playback
■
This feature allows the VCR to automatically start playing when you insert a tape with the safety tab
removed.
Press [SETUP] and select
“FUNCTIONS”.
Move
to “FUNCTIONS” with [ ] and press
[ENTER].
Press [ENTER] to switch between ON
and OFF.
- Select ON if you want a tape with its safety
tab removed to start playing automatically
when the tape is inserted.
- Select OFF if you do not want a tape with
its safety tab removed to start playing
automatically.
1
1
2
2
SETUP
CLOCK SET
TIMER RECORDINGS
CHANNEL SET
FUNCTIONS
LANGUAGE SELECT
FUNCTIONS
Auto Play:
ON
Auto TV/VCR:
ON
Index Search
Go-To Search
Move:
Select:
End:
SETUP
ENTER
Move:
Select:
End:
SETUP
ENTER
Switch the VCR to TV or VCR mode automatically
■
This feature controls whether the TV/VCR switch changes automatically to the VCR mode when the VCR is turned on.
Press [SETUP] and select “FUNCTIONS”.
Move
to “FUNCTIONS” with [ ] and press [ENTER].
Press [ENTER] to switch between ON
and OFF.
- Select ON if you want the VCR to switch to
the VCR mode when the VCR is turned on
or a cassette is inserted. This only applies if
you connect the ANT.IN and RF OUT jacks
of your VCR and TV and watch your VCR on
channel 3 of your TV.
- Select OFF if you want the VCR to remain
in TV mode. This is useful if you watch your
VCR on the TV’s video input and you don’t
want your antenna/cable signal interrupted
by the VCR.
2
2
1
1
FUNCTIONS
Auto Play:
ON
Auto TV/VCR:
ON
Index Search
Go-To Search
Move:
Select:
End:
SETUP
ENTER
1
1
Use PLAY, REW, or FF to locate the point on the tape you would like to mark as
0:00:00.
2
2
Press [DISPLAY] to display the tape counter on the screen.
3
3
Press [CLEAR] to reset the tape counter to 0:00:00.
4
4
You can continue to play the tape or perform other functions with the VCR.
Marking a tape for zero search