Marantz SR6003 - Manual (Page 48)

45
ENGLISH
BASIC
CONNECTIONS
BASIC OPERA
TION
ADV
ANCED
CONNECTIONS
SETUP
ADV
ANCED
OPERA
TION
TROUBLESHOOTING
OTHERS
NAMES AND
FUNCTION
ADV
ANCED
OPERA
TION
TV AUTO ON/OFF FUNCTION
This function allows the component connected to the
TV-VIDEO in jack to control the power (ON/OFF) to
the unit.
AUTO POWER ON
1. Be sure the TV auto mode is Enabled. (Refer to
page 37:)
2. Connect your TV TUNER (etc) to the TV-
VIDEO in terminal. Be sure to connect the
VIDEO input.
3. Turn OFF the power to the TV TUNER and turn
standby to the unit.
4. Turn ON the TV TUNER and tune in a receivable
station.
5. When the station is received, this unit turns ON
and TV is selected automatically.
AUTO POWER OFF
1. In the above situation, turn the TV TUNER OFF
or select a channel that does not contain any
broadcast.
2. The power to the unit switches to STANDBY
after approx. 5 minutes.
Notes:
• AUTO POWER OFF is canceled if this unit is set to
a source other than TV.
The function reactivates when TV is selected again.
• Some TV broadcasts may cause the TV AUTO
FUNCTION to turn ON.
• The S-Video, component and HDMI terminal does
not support “TV AUTO ON/OFF” function.
• This function is inactive when STANDBY MODE
is set to ECONOMY. To use this function, set
STANDBY MODE to NORMAL.
LIP.SYNC
Depending on the image device (TV, monitor,
projector, etc.) connected to the unit a time lag can
occur between image signal processing and audio
signal processing. Though minor, this time lag can
interfere with movie and music enjoyment. The LIP.
SYNC feature delays the audio signal with respect
to the image signal output from the unit to correct
the time lag between the sound and image. It can be
operated with the “LIP SYNC” and
1 and 2 cursor
buttons of the remote controller. Set the remote
controller to the AMP mode before operating the
LIP.SYNC feature. The initial setting is OFF (0 ms).
The time lag can be adjusted in 10 ms steps up to
200 ms.
Watch the picture on the image device (i.e., TV,
monitor, projector, etc.) as you adjust the time lag.
Note:
• The LIP.SYNC feature turns OFF (0 ms) in the
SOURCE/PURE DIRECT mode. When the
SOURCE/PURE DIRECT mode is deactivated, the
set value of the LIP.SYNC feature is automatically
restored.
• Even if you do not correct the time lag manually this
way, audio and video are automatically synchronized
when the unit is connected to TV or Projector
supporting Auto Lipsync Correction in HDMI 1.3a.
For instructions on Auto Lipsync Correction, see
page 38.
DUAL BACKUP MEMORY
The unit stores settings information in nonvolatile
memory even when the main power supply is turned
off. Using the Dual Backup Memory function, you
can write settings information to another memory
area to back up saved settings for recovery anytime
as needed.
BACKUP
Set up the unit in the state for which you want to
store the settings. Hold the MEMORY and ENTER
buttons on the front panel simultaneously for at least
3 seconds.
“MEMORY SAVING” is displayed and the unit’s
settings are saved. The stored settings information
is retained until Dual Backup Memory is used again
and the information is overwritten.
M E M O R Y S A V I N G
Note:
• The following settings values cannot be backed
up.
• Main ZONE Volume
• ZONE A Volume
• ZONE Speaker A Volume
RECOVERY OF MEMORY
Recover backed up settings as follows.
Hold the MEMORY and MENU buttons on the front
panel simultaneously for at least 3 seconds.
“MEMORY LOAD” is displayed and the unit’s stored
settings are reapplied.
The unit temporarily enters standby mode. If there is
no backup data, “NO BACKUP” is displayed and no
data is recovered.
M E M O R Y L O A D
N O B A C K U P
Note:
• Because the following settings values are
not backed up, each Volume value is set to
Minimum.
• Main ZONE Volume
• ZONE A Volume
• ZONE Speaker A Volume