Marantz SR8001 - Manual (Page 44)

41
ENGLISH
TEMPORARILY TURNING OFF THE SOUND
2 3 1
5 6 4
8 9 7
OK
PREV MUTE
MENU EXIT
GUIDE
TEST CH.SEL
LIP.SYNC
SURR
7.1CH ATT SPK-AB
DISP OSD SLEEP
MUTE
To temporarily silence all speaker outputs such as
when interrupted by a phone call, press the MUTE
button on the remote.
This will interrupt the output to all speakers and the
head-phone jack, but it will not affect any recording
or dubbing that may be in progress.
When the system is muted, the display will show
“MUTE” .
Press the MUTE button again to return to normal
operation.
USING THE SLEEP TIMER
2 3 1
5 6 4
8
0
9 7
MEMO CLEAR
PREV MUTE
MENU EXIT
GUIDE
TEST CH.SEL
LIP.SYNC
SURR
7.1CH ATT SPK-AB
DISP OSD
THX
SLEEP
9
SLEEP
To program the SR7001 for automatic standby, press
the SLEEP button on the remote.
Each press of the button will increase the time before
shut down in the following sequence.
OFF 10 20 30 40
90 80 70 60 50
The sleep time will be shown for a few seconds in the
display on the front panel, and it will count down until
the time has elapsed.
When the programmed sleep time has elapsed, the
unit will automatically turn off.
Note that the SLEEP indicator on the display will
illuminate when the Sleep function is programmed.
To cancel the Sleep function, press the SLEEP
button until the display shows “SLEEP OFF” and the
SLEEP indicator will disappear.
VIDEO CONVERT
ANALOG VIDEO CONVERSION
The SR7001 is equipped to convert video signals
for monitor output. Because of this, indifferent of
the connection (VIDEO, S-VIDEO, COMPONENT
VIDEO) between the playback device and the
SR7001, listening and viewing are possible with a
single higher grade cable between the MONITOR
OUT terminal of the SR7001 and the monitor.
UP-CONVERSION FROM ANALOG VIDEO
SIGNALS TO HDMI
The up-conversion feature of the SR7001 can output
the input analog video signals (for component video
signals of 480i/576i, 480p/576P, 1080i and 720p
resolution, and S-Video and Video (composite)
of 480i/576i resolution) to the HDMI MONITOR
terminal.
Notes:
• HDMI video input is only output to the HDMI
MONITOR OUT terminal of the SR7001. If
connecting a playback device such as a DVD
player to the HDMI input jack, connect the HDMI
MONITOR OUT terminal of the SR7001 to a TV
monitor.
• This mode is unavailable for the REC out terminal.
• This mode is unavailable for still picture, fast
forward and reverse play on video component.
• If, while attempting to use the video convert feature,
the SR7001 cannot synchronize with the display
device, “NO SIGNAL” appears on the monitor or
noise is generated, this feature cannot be used. All of
these signs are caused by equipment incompatibility;
there is nothing wrong with the SR7001.
If this occurs, set “VIDEO CONVERT” in the
“VIDEO SETUP” menu to “DISABLE”. Next,
connect the video input signal to the display component
via the MONITOR OUT terminal under VIDEO and
the S-video input signal to the display component via
the MONITOR OUT terminal under S-VIDEO.
• The video convert feature constantly monitors
input video signals and determines whether to
convert the input signals or not. However, some
input video signals cannot be detected correctly.
If this occurs, set “VIDEO CONVERT” in the
“VIDEO SETUP” menu to “DISABLE”.
• For optimal video performance, THX recommends
setting the “VIDEO CONVERT” mode “DISABLE”.
CONNECTION EXAMPLE
• When a monitor is connected to the HDMI
MONITOR OUT terminal of the SR7001
DIGITAL R L VIDEO S-VIDEO AUX 1 INPUT AUDIO
VOLUME
UP DOWN
STANDBY PHONES
READY INPUT SELECTOR AV SURROUND RECEIVER SR8001
MultEQ ENTER MENU PURE DIRECT THX 7.1CH INPUT MODE AUTO MULTI
A/B
T-MODE MEMORY CLEAR DISPLAY EXIT SPEAKERS
BAND
MIC
PURE DIRECT
SURROUND SPEAKER MULTI
DSD
POWER ON/STANDBY
VIDEO
or S-VIDEO
or component
HDMI or HDMI
Notes:
• If the resolution of the component video signal input
from the playback device is other than 480i/576i,
480p/576P, 1080i or 720p, images are not output
from the HDMI MONITOR OUT terminal of the
SR8001.
• If the resolution of the S-Video or Video signal input
from the playback device is other than 480i/576i,
images are not output from the HDMI MONITOR
OUT terminal of the SR7001.
• When a monitor is connected to the VIDEO or S-
VIDEO MONITOR OUT terminals of the SR7001
DIGITAL R L VIDEO S-VIDEO AUX 1 INPUT AUDIO
VOLUME
UP DOWN
STANDBY PHONES
READY INPUT SELECTOR AV SURROUND RECEIVER SR8001
MultEQ ENTER MENU PURE DIRECT THX 7.1CH INPUT MODE AUTO MULTI
A/B
T-MODE MEMORY CLEAR DISPLAY EXIT SPEAKERS BAND
MIC
PURE DIRECT
SURROUND SPEAKER MULTI
DSD
POWER ON/STANDBY
L C R SL S SR LFE DIGITAL SURROUND V-OFF DISP MULTI AUTO TUNED ST SPKR A B NIGHT PEAK ANALOG DIGITAL ATT SLEEP SURR DIRECT AUTO DISC 6.1 MT X 6.1 EQ PCM AAC
VIDEO
or S-VIDEO
VIDEO
or S-VIDEO
or component
HDMI
Notes:
• The HDMI video signal input from the playback
device is not output from the VIDEO or S-VIDEO
MONITOR OUT terminals of the SR7001.
• If the resolution of the component video signal input
from the playback device is other than 480i/576i,
it is not output from the VIDEO or S-VIDEO
MONITOR OUT terminals of the SR7001.
• When a monitor is connected to the COMPONENT
VIDEO MONITOR OUT terminal of the SR7001
DIGITAL R L VIDEO S-VIDEO AUX 1 INPUT AUDIO
VOLUME
UP DOWN
STANDBY PHONES
READY INPUT SELECTOR AV SURROUND RECEIVER SR8001
MultEQ ENTER MENU PURE DIRECT THX 7.1CH INPUT MODE AUTO MULTI A/B T-MODE MEMORY CLEAR DISPLAY EXIT SPEAKERS BAND
MIC
PURE DIRECT
SURROUND SPEAKER MULTI
DSD
POWER ON/STANDBY
VIDEO
or S-VIDEO component
or component
HDMI
Notes:
• The HDMI video signal input from the playback
device is not output from the COMPONENT
VIDEO MONITOR OUT terminal of the SR7001.
Notes of OSD menu system:
• The setup menu can be displayed through all
video out terminals (“HDMI”, “COMPONENT”,
“SVIDEO” and “VIDEO”).
• OSD information is output only to the VIDEO and
S-VIDEO MONITOR OUT terminals.
OSD information is also output when the video
conversion feature is on and the video signal input
to the VIDEO or S-VIDEO input jack of the SR7001
is converted and output from the COMPONENT
VIDEO or HDMI MONITOR OUT terminals.
I/P CONVERT
The video circuit of the SR7001 is equipped with an
I/P conversion feature.
When this feature is on, 480i/576i analog video
signals (VIDEO, S-VIDEO or COMPONENT VIDEO)
input from a playback device can be converted
to 480p/576p and progressively output to the
COMPONENT VIDEO or HDMI MONITOR OUT
terminals of the SR7001.
(For setting instructions, see page 35)