Panasonic WV-NS324 - Manual (Page 42)

-43-
8. Dwell Time
Move the cursor to DWELL TIME, and select a time
with the Joystick.
When the time specified here elapses after motion
detection, the camera will notify the connected
device of the alarm activation. The default setting is
2 seconds.
Selectable times (seconds): 2s, 5s, 10s, 30s
Important Notices:
• The following conditions should be met for motion
detection.
1) The picture size on the screen should be larg-
er than 1/48 of the actual picture size.
2) The contrast ratio between the object and the
background picture should be more than 5 %
at the maximum detection level.
3) The time it takes the object to move from one
end of the screen to the other should be more
than 0.1 seconds.
• Also under the following conditions, mask or adjust
the detection level to prevent malfunction.
1) When leaves, or curtains, etc., are swayed by
the wind.
2) When a picture has a high noise content due
to low light conditions.
3) When the object is illuminated by lighting
equipment that constantly turns on and off.
● Special Menu (SPECIAL)
This menu allows you to adjust and set up the following
items and functions: chroma level, aperture level,
pedestal level, demo mode function, digital noise
reduction function and refresh function.
You can also reset your parameters to the values preset
at the factory.
This menu lets you adjust and set up the picture quality
to meet your requirements.
• Move the cursor to SPECIAL and press the [F2]
button of the WV-CU550CJ. The special menu
appears on the monitor screen.
For the WV-RM70, keep pressing the Right and Left
switches simultaneously for 2 seconds or more.
(1) Chroma Level Setting (CHROMA GAIN)
(2) Aperture Level Setting (AP GAIN)
(3) Pedestal Level Setting (PEDESTAL)
(4) Camera Phase (Hue) Setting (HUE)
1. Move the cursor to HUE. The "I" cursor appears in
inverse video.
2. While observing the vector scope or color video
monitor, adjust the chroma phase (hue) by using
the joystick. The cursor moves to the right or left.
To reset to the factory setup, press the [F2] button
of the WV-CU550CJ.
(For the WV-RM70, keep pressing the Right and
Left switches simultaneously for 2 seconds or
more.)
(5) Digital Noise Reduction (DNR)
DNR may be used to improve quality under low
light conditions.
LOW: DNR level is low.
HIGH: DNR level is high.
(6) Demonstration Display (DEMO MODE)
You can output the upside-down image by using
Demo Mode.
Note: Never face the camera at a place exposed to
strong light sources for a long time. If light
sources such as spot light cause burn-in on the
display screen, part of image may discolor due
to deterioration of the color filter in the CCD
when changing the aim of the camera etc.
2S 5S 10S 30S
** SET UP **
CAMERA ID ON
O
ALC/MANUAL ALC O
SHUTTER OFF
AGC ON(MID)
SYNC INT
WHITE BAL ATW
O
AF MODE MANUAL
EL-ZOOM ON
SENS UP OFF
MOTION DET OFF
RET SPECIAL
O
** SPECIAL **
CHROMA GAIN ••••
| ••••
AP GAIN ••• | •••••
PEDESTAL ••• | •••••
HUE •I•••••••
– +
DNR LOW
DEMO MODE OFF
REFRESH
→
PUSH SET
CAMERA RESET
→
PUSH SET
RET
** SPECIAL **
CHROMA GAIN ••••
| ••••
AP GAIN ••• | •••••
PEDESTAL ••• | •••••
HUE •I•••••••
– +
DNR LOW
DEMO MODE OFF
REFRESH
→
PUSH SET
CAMERA RESET
→
PUSH SET
RET