Panasonic DP-MB350 - Manual (Page 60)

9. Programmable Features
60
Setting the recording paper
type
{#}{ 3 }{ 8 }{ 3 }
{ 1 } “ Plain Paper ” (default): 75 g/m
2
to 90 g/m
2
(20 lb to 24 lb) paper.
{ 2 } “ Thin Paper ”: 64 g/m
2
to 75 g/m
2
(17 lb to 20 lb) paper.
{ 3 } “ Thick Paper ”: 90 g/m
2
to 165 g/m
2
(24 lb to 44 lb) paper.
Note:
L This setting is valid for both the standard input tray and the lower input tray.
L “ Thick Paper ” will not be displayed if any of the paper input tray settings
are changed to “ #2 ” or “ #1+#2 ”:
– fax (feature #440 on page 64).
– copy (feature #460 on page 67).
– PCL
®
(feature #760 on page 69).
– scan to email print feature (feature #565 on page 74).
Setting the paper input tray to
use for lists and reports
printing
{#}{ 3 }{ 9 }{ 0 }
This feature will be displayed only when the lower input tray is installed (page
79).
{ 1 } “ #1 ” (default): Standard input tray
{ 2 } “ #2 ”: Lower input tray
{ 3 } “ #1+#2 ”
Note:
L To select “ #2 ”, select “ Plain Paper ” or “ Thin Paper ” for the recording
paper type setting (feature #383 on page 60).
L To select “ #1+#2 ”,
– select the same paper size for the standard input tray (feature #380 on
page 59) and lower input tray (feature #382 on page 59). If either is
changed, “
#1 ” will be selected automatically.
– select “ Plain Paper ” or “ Thin Paper ” for the recording paper type
setting (feature #383 on page 60).
Setting the waiting time for
the power save mode
{#}{ 4 }{ 0 }{ 3 }
To set the length of time before the unit enters power save mode.
{ 1 } “ 5min ”: 5 minutes
{ 2 } “ 15min ” (default): 15 minutes
{ 3 } “ 30min ”: 30 minutes
{ 4 } “ 1h ”: 1 hour
Note:
L When in power save mode, the unit needs to preheat the fuser unit before
it can begin printing.
Holding the previous contrast
setting
{#}{ 4 }{ 6 }{ 2 }
{ 0 } “ Disabled ” (default): Deactivates this feature.
{ 1 } “ Enabled ”: The unit will hold the previous setting.
Note:
L The previous setting will be held individually for copying and sending faxes.
Setting the default operation
mode
{#}{ 4 }{ 6 }{ 3 }
To select the default operation mode when the selected time of the mode timer
(feature #464) passes.
{ 1 } “ Copy ” (default): Copy mode is selected as default.
{ 2 } “ Fax ”: Fax mode is selected as default.
Note:
L You cannot select the scan mode using this feature.
Setting the default operation
mode timer
{#}{ 4 }{ 6 }{ 4 }
To set the timer before returning to the default operation mode (feature #463).
{ 0 } “ Off ”: Deactivates this feature.
{ 1 } “ 30s ”: 30 seconds
{ 2 } “ 1min ” (default): 1 minute
{ 3 } “ 2min ”: 2 minutes
{ 4 } “ 5min ”: 5 minutes
Feature/Code Selection