Panasonic AJ-HD1700PE - Manual (Page 52)

52
Function menus
<CUE>
Moving to registered points
The highlighting on the registered point display area is
moved by turning the ADJUST dial. It is moved in the
ascending order of points when the dial is turned
clockwise and in the descending order of points when
it is turned counterclockwise. When “AUTO” has
been selected as the
(PAGE) setting on the
<CUE SHIFT> menu, the highlighting can be moved
also to the previous or next page.
• Depending on the setting selected for
(ROTATE) on the <CUE SHIFT> menu, the
following applies to moving the highlighting in the
ascending order of points.
When “OFF” is set:
The highlighting cannot be moved from page 9 to
page 0.
When “ON” is set:
The highlighting can be moved from page 9 to page 0.
• In moving in the descending order of points, the
highlighting cannot be moved from page 0 to page 9.
Search point and registered point
operations
Each time the (MODE) button of the <CUE>
menu is pressed, the search mode and cue point
registration mode are switched alternately. Perform
the search point or registered point operations in the
respective mode.
• When the power is turned on, the search point or
registered point, whichever was established when
the power was last turned off, is established.
• When the setting for (PAGE) or (ROTATE)
on the <CUE SHIFT> menu has been changed,
“01” (page 0/point no.1) is set for both the search
and registered points.
Cue point registration mode
It is possible to register points to which the tape is to
be prerolled. When the display page has been
changed using the
(PREV) or (NEXT) button
on the <CUE> menu, the following applies depending
on the setting for
(PAGE) on the <CUE SHIFT>
menu.
When “MANU” is set:
Both the search and registered points move to the top
of the changed page.
When “AUTO” is set:
Only the registered point moves to the top of the
changed page; the search point does not move.
F3
F2 F1
F4 F3
F3
F4
F3
A maximum of 60 cue points can be set on these menu
screens. When “AUTO” has been selected as the
(PAGE) setting on the AUTO PAGE mode <CUE SHIFT>
menu, up to 10 pages of cue points with 6 cue points on
each page can be managed on a page-by-page basis.
The 60 cue points are indicated using the page number
display and registered point display areas.
<Note>
Cue points cannot be registered, prerolled, etc. if a
setting other than “ENA” has been selected as the setup
menu item No.001 (LOCAL ENA) setting in the REMOTE
mode.
F3
F1 SHIFT F2 F3 F4 F5 F6
Page number display area
Registered point display area
Cue point data display areas
Page number display area
The page number from 0 to 9 is indicated here.
Registered point display area
On each page, six cue point data managed by
registered point numbers are displayed. A point
whose registered point number is highlighted is
targeted for registration and search.
Shown below is the correlation between the page
numbers and registered point numbers.
Page no. Registered points Page no. Registered points
0 01–06 5 51–56
1 11–16 6 61–66
2 21–26 7 71–76
3 31–36 8 81–86
4 41–46 9 91–96
Page operations
Pages can be scrolled in the forward or reverse direction
using the
[F1] (PREV) or [F2] (NEXT) function buttons.
• Depending on the setting selected for [F4] (ROTATE)
on the <CUE SHIFT> menu, the following applies to
scrolling pages in the forward direction.
When “OFF” is set:
Page 0 cannot be scrolled forward from page 9.
When “ON” is set:
Page 0 can be scrolled forward from page 9.
• In scrolling pages in the reverse direction, page 9
cannot be scrolled in reverse from page 0.
F1 SHIFT F2 F3 F4 F5 F6
F4
F1 F2