Parker Products COMPAX-M /-S (L) - Manual (Page 104)

Operating Instructions COMPAX-M / -S
Cam controller with compensation for switching delays
104
8.4.15 Cam controller with compensation for switching delays
With the function "Cam controller", you can switch 4 actuators (switch elements)
dependent on position.
♦ The switching positions are fixed positions within the positioning range.
♦ The reference value for the switching positions can be selected from:
the position actual value (S1) or
the position set point or
the absolute value (S12)
♦ The switching delay of the actuators is compensated for dependent on the speed.
Outputs O9 ... O12
Parametrization occurs via variables in the range V50 ... V70.
No.: Contents Unit min stand
ard max valid
from
V50 Operation mode cam controller
0: inactive
1: position actual value
(without consideration of P1 and P215)
2: position set point
(without consideration of P1 and P215)
3: reserved
4: S1 (position actual value)
Number range: +/- 4 mill. units (P90)
5: position set point
Number range: +/- 4 mill. units (P90)
6: absolute value (S12)
Number range: +/- 2048 units (P90)
0 0 VP
V51 Polarity O9...O12 Valence
Bit 9: Polarity O9 256
Bit 10: Polarity O10 512
Bit 11: Polarity O11 1024
Bit 12: Polarity O12 2048
If the corresponding bit is set, then the
relevant output is inverted.
0 0 3840 VP
V52 reserved VP
V53 reserved VP
V54 reserved VP
V55 Position control cam 1 (O9) on* P90 -4 000 000 0.00 +4 000 000 VP
V56 Switch-on lag control cam 1 ms 0 0 1000 VP
V57 Position control cam 1 (O9) off* P90 -4 000 000 0.00 +4 000 000 VP
V58 Switch-off lag control cam 1 ms 0 0 1000 VP
V59 Position control cam 2 (O10) on* P90 -4 000 000 0.00 +4 000 000 VP
V60 Switch-on lag control cam 2 ms 0 0 1000 VP
V61 Position control cam 2 (O10) off* P90 -4 000 000 0.00 +4 000 000 VP
V62 Switch-off lag control cam 2 ms 0 0 1000 VP
V63 Position control cam 3 (O11) on* P90 -4 000 000 0.00 +4 000 000 VP
V64 Switch-on lag control cam 3 ms 0 0 1000 VP
V65 Position control cam 3 (O11) off* P90 -4 000 000 0.00 +4 000 000 VP
V66 Switch-off lag control cam 3 ms 0 0 1000 VP
V67 Position control cam 4 (O12) on* P90 -4 000 000 0.00 +4 000 000 VP
V68 Switch-on lag control cam 4 ms 0 0 1000 VP
V69 Position control cam 4 (O12) off* P90 -4 000 000 0.00 +4 000 000 VP
V70 Switch-off lag control cam 4 ms 0 0 1000 VP
* The switching processes described apply for increasing setpoint and P215=0;
with decreasing setpoint switch off occurs at the same position where switch on
previously occured.
The variables for parametrization of the cam controller are not password
protected!
Function of the
cam controller:
Outputs of the cam
controller
Parametrization of
the cam controller
POSA
POSR
SPEED
ACCEL
OUTPUT
Password
SPEED
SYNC
Mark
reference
POSR
SPEED
POSR
OUTPUT
Cam
controller
WAIT
GOTO
GOSUB
RETURN
END
REPEAT
IF I..
Comparison
WAIT Start
GOTO /
GOSUB EXT
IF Error/ Stop
Arithmetic
Position
monitoring
Idle display
Speed
monitoring
Engage /
disengage
brake / final
stage
Variable
voltage