Nokia CC100 - Manual (Page 43)

CC100Master Bridge User’s Guide
40
dconfig
Dump all configurations/settings.
default
Reset all settings to factory default, except Password.
diag
-t <mac>
-r <mac>
On-line EP connection diagnosis.
-t: downstream SNR diagnosis(from Master to EP)
-r: upstream SNR diagnosis(from EP to Master)
<mac> : EP MAC <mac> to be diagnosed
dir
Show detail file information resides in flash ROM. Include
‘Working Area’ and ‘Upload Area’, refer
Figure 4 . The listed
filenames are,
‘
bootcode ’: boot loader
‘ sysfw4m ’: system firmware
‘ G1C28H21M ’: Master HCNA driver
‘ G0C28H20Ep ’: 3010 EP HCNA driver
‘ G1C28H21Ep ’: 3110 EP HCNA driver
‘ diagsw ’: 3010 diagnosis utility file
‘ diagsw1 ’: 3110 diagnosis utility file
Accompanying with file id, file version, file date, and file size.
dns
[ -s <pri/sec> <ip>] Display or set up DNS server setting.
-s
pri <ip> : set up Primary DNS server’s IP
-s sec <ip> : set up Secondary DNS server’s IP
exit Close the Telnet console.
quit Close the Telnet console.
ep
[ -c <hostcnt>]
[ -n <note>]
[ -u <uprate index>]
<mac>
Set up the EP Properties Profile related setting values.
<hostcnt> : EP Host Limit setting value (0~255), default 255
<note> : EP Note setting value
<uprate index> : EP Upstream Rate setting value ( 0~1563,
*64Kbps), default 0 for unlimited
<mac> : designated EP MAC to configure
ephpnareboot
(Smart EP)
-m <mac> Reset remote Smart EP device
epstat
(Smart EP)
-m <mac>
[ -r ]
Display remote Smart EP port statistics for port
LAN1/LAN2/HCNA.
-r: reset all port statistics counter to 0
epswc
(Smart EP)
-m <mac>
[ -t ]
[ -u ]
[ -r ]
[ -d ]
[ -p <lan1/lan2/hpna>
[ -l <up/down>]
[ -s <auto /10h /10f
/100h /100f>]
[ -f <on/off>]]
Display or set up remote Smart EP built-in switch Ethernet
properties
-t: display EP switch settings
-u: display EP switch/port status
-r: reset EP switch
-d: reset EP switch’s eeprom settings to factory default
-p: configure EP port LAN1/LAN2/HCNA
-l: link,
<up/down> : force current port to link up or down, i.e.
enable/disable current port
-s: current port Ethernet mode setting,
<auto> : auto-negotiation mode
<10h/10f/100h/100f> : 10/100Mbps, half/full-duplex mode
-f: current port Ethernet flow-control setting,
<on/off> : turn on /off flow control
epswigmp
epswqosq
epswqosrate
epswqostc
epswtagvlan
(Smart EP)
-m <mac> Refer swigmp , swqosq , swqosrate , swqostc , swtagvlan for the
same functionality, but operate on remote Smart EP with
designated MAC address
<mac>
filter
[ -s <set>
[ -c <act/deact>]
[ -a <ip> -m <mask>]
[ -t <allow/deny>]
[ -w <allow/deny>]
Display or set up the filter rule set, refer the section “ Allow
Source ” for IP <ip> and Subnet Mask setup <mask> .
<set> : filter set index, total 16 set (0~15)
<act/deact> : activate or de-activate the rule set
<allow/deny> : allow or deny the protocol