Snmptrapserver, Snmptrapsetup, Sntp – Nokia CC100 User Manual
Page 47: Stat, Swconfig, Swigmp, Swqos, Swqosrate, Swqostc, Swsmac
CC100Master Bridge User’s Guide
44
snmptrapserver
[
-s
<set>
[
-c
<act/deact>]
[
-p
<port>]
[
-a
<ip>]
[
-m
<community>] ]
Display or set up SNMP trap server(s) configuration.
<set>
:
trap server index, at most 5 servers (0~4)
<act/deact>
: activate or de-activate trap server IP
<ip>
<port>
: SNMP trap UDP port number (0~65535), default
162
<ip>
: trap server IP address
<community>
: trap server community name, default ‘
public
’
snmptrapsetup
[
-l
<on/off>]
[
-u
<on/off>]
[
-s
<on/off>]
[
-d
<on/off>]
Enable or disable specified trap type,
<on/off>
: turn on or turn off this trap type, default is
on
-l: logon/logoff trap
-u: upload/upgrade firmware/driver trap
-s: EP on-line status changed trap
-d: EP diagnosis trap
sntp
[
-c
<act/deact>]
[
-r
<refresh time>]
[
-z
<time zone>]
[
-s
<set> -a
address
]
Display or set up SNTP configuration for
.
<act/deact>
: activate or de-activate SNTP service for system
time
<refresh time>
: query SNTP server period, default
60
minutes
<time zone>
: ‘+
hh
:
mm
’ or ‘-
hh
:
mm
’ to GMT time,
hh
for hours
and
mm
for minutes, default ‘
+00:00
’
<set>
: 2 registered SNTP server set(0~1)
address: SNTP server host name or IP address in current set
stat
[
-r
]
Display port statistics for port LAN1/LAN2/HCNA.
-r: reset all port statistics counter to 0
swconfig
[
-p
<lan1/lan2>
[
-s
<auto /10h /10f
/100h /100f>] ]
Display or set up Ethernet port LAN1/LAN2 properties
<lan1/lan2>
: configure LAN1 or LAN2 port
<auto>
: auto-negotiation mode
<10h/10f/100h/100f>
: 10/100Mbps, half/full-duplex mode
swigmp
[
-c
<on/off>]
[
-t
<QueryInterval
(4~510, even
number)>]]
Display or set up IGMP v2 snooping configuration
<on/off>
: enable or disable built-in IGMP v2 snooping function,
default is off
<Query Interval>
: expiry timer to age learned Multicast MAC if
no IGMP query frame received from the router, default
is
248
seconds (range from 4 to 510 in even)
swqos
[
-q
<queue>
[
-w
<weight>]
[
-d
<discard mode>]]
Display or set up the QoS configuration, include priority queue,
service weight and discard ratio while congestion, refer
for more.
<queue>
: select queue index (0~3) to configure, as q0(lowest
priority)/q1/q2/q3(highest priority)
<weight>
: assign the queue with service weight(1~15), default
1
for q0,
2
for q1,
3
for q2 and
4
for q3
<discard mode>
: choose the discard mode(0~3) for queue
utilization, default
0
for 0%.
1 for 25%, 2 for 50% and 3 for 75%. refer
for more.
swqosrate
[
-p
<lan1/lan2>
[
-d
<tx/rx>]
[
-c
<on/off>]
[
-r
<N (1~1563
rate=N*64kbps)>] ]
Display or set up the LAN1/LAN2 maximum rate. refer
for more.
<lan1/lan2>
: configure LAN1 or LAN2 port
<tx/rx>
:
direction, incoming(rx) or outgoing(tx)
<on/off>
: enable or disable control on this direction
<N>
: the setup max rate (multiply value by 64kbps). Range
from 0 to 1563, bandwidth control is invalid if N >= 1563
swqostc
[
-s
<set>
[
-c
<act/deact>]
[
-p
<port>
-q
<queue>] ]
Display or set up the QoS configuration for TCP/UDP traffic
classification, to assign higher priority for total 8 different
TCP/UDP protocols
<set>
:
rule set index, at most 8 set (0~7)
<act/deact>
: activate or de-activate this set
<port>
: TCP/UDP port number (0~65535),
<queue>
: select queue index (0~3) for this rule set, as
q0(lowest priority)/q1/q2/q3(highest priority)
swsmac
[
-m
<mac>]
Display or set up the static MAC entry, total 8 entries of MAC