Napoleon Fireplaces Castlemore GDS26N - Manual (Page 19)

19
W415-0607 / A / 01.18.08
FIGURE 30
FIGURE 31
R E S T R I C T O R
PLATE
1. Remove the front and the door from the stove.
2. Remove the screws securing the baffl e plate. Figure 31.
Note: The baffl e rests on two screws that are attached to the
back of the fi rebox.
3. Using the screws supplied, attach the restrictor plate as
show in Figure 31.
4. Replace the baffl e.
BAFFLE PLATE
SCREWS
FIGURE 32
GAS INSTALLATION
This Mobile/Manufactured Home Listed appliance comes
factory equipped with a means to secure the unit. The stove
is equipped with two 1/4" diameter holes located in the front
left and right corners of the base. For mobile home installa-
tions, the stove must be fastened in place. Use #10 hex head
screws, inserted through the holes in the base to secure.
Always turn off the pilot and the fuel suuply at the source,
prior to moving the mobile home. After moving the mobile
home and prior to lighting the stove, ensure that the logs are
positioned correctly.
MOBILE HOME INSTALLATION
Proceed once the vent installation is complete.
1. Move the stove into position and secure to the fl oor
through the 1/4" holes located at either side of the base.
2. The stove is designed to accept 3/8" gas supply line.
The stove is equipped with a 3/8" manual shut-off valve and
fl exible connector. Do not kink fl exible connector.
3. Connect the gas supply in accordance to local codes.
In the absence thereof, install according to the National
Installation Code.
4. When fl exing any gas line, support the gas valve so that
the lines are not bent or kinked.
5. Check for gas leaks by brushing on a soap and water
solution.
DO NOT USE OPEN FLAME.
Purge all gas lines with the glass door of the stove re-
moved. Assure that a continuous gas fl ow is at the burner
before re-installing the door.
This appliance is certifi ed to be installed as an OEM (Origi-
nal Equipment Manufacturer) installation in a manufactured
home or mobile home and must be installed in accordance
with the manufacturer’s instructions and the Manufactured
Home Construction and Safety Standard, Title 24 CFR, Part
3280, in the United States or the Mobile Home Standard,
CAN/CSA Z240 MH Series, in Canada. This appliance is
only for use with the type(s) of gas indicated on the rating
plate. A conversion kit is supplied with the mobile home
appliance.
This appliance is certifi ed to be installed in an aftermarket
permanently located, manufactured (mobile) home, where
not prohibited by local codes.
This stove is only for use with the type of gas indicated on
the rating plate. This stove is not convertible for use with
other gases, unless a certifi ed kit is used.
Conversion Kits
The mobile home appliance is fi eld convertible between
Natural Gas (NG) and Propane (LP).
To convert from one gas to another consult your Napoleon®
dealer/distributor.
Shown
in “OFF”
position.
Manual
Shut-off Valve
A B
Supply pressure can be checked by turning screw (A)
counter-clockwise until loosened and then placing pressure
gauge tubing over the test point. Gauge should read 7”
(minimum 4.5”) water column for natural gas or 13” (11”
minimum) water column for propane. Check that main burner
is operating on “HI”.
Manifold pressure can be checked the same as above using
screw (B). Gauge should read 3.5” water column for natural
gas or 10” water column for propane. Check that main burner
is operating on “HI”.
AFTER TAKING PRESSURE READINGS, TIGHTEN
SCREWS FIRMLY TO SEAL. DO NOT OVERTORQUE.
LEAK TEST