Omnitron Systems Technology iConverter 10/100M2 Standalone Module - Manual

iConverter 10/100M2 Standalone Module QUICK START GUIDE
The Omnitron iConverter ® 10/100M2 is a carrier-
class Network Interface Device (NID) that
provides 10BASE-T or 100BASE-TX (10/100) to
100BASE-FX Fiber media conversion with
integrated management.
The 10/100M2 conforms to Ethernet in the
First Mile (EFM) fiber standards to support
Fiber-to-the-X (FTTX) Metropolitan access
and Enterprise LAN networks. 10/100M2
media converters are used to provide managed copper demarcation points at the
customer premises and network edge, offering service provisioning functions, such as
Quality of Service and Bandwidth Control (rate-limiting) capabilities.
The 10/100M2 can be managed using Omnitron’s NetOutlook TM SNMP Management
Software, 3rd Party SNMP Client, Telnet or the Command Line Interface (CLI).
For more information, including the complete User Manual on the 10/100M2 module,
access Omnitron’s documentation download web page to view all relevant documents:
http://www.omnitron-systems.com/downloads.php
INSTALLATION PROCEDURE
1) Configure DIP-Switches
2) Install Standalone Module and Connect Cables
3) Configure Module via Command Line Interface
4) Verify Operation
1) CONFIGURE DIP-SWITCHES
DIP-SWITCH BANK 1
SW1 - UTP/FIBER PAUSE ENABLE
When a port is operating in
Auto-Negotiation (AN), its
Pause operation mode is
determined by the Pause
capability advertised during
AN between itself and the
link partner. The port
advertises its Pause
capability (Symmetrical or
No Pause) during AN
based on the Pause
Disable/Enable DIP-switch setting.
When a port is operating in Manual mode, its Pause operation mode is based on the
Pause Disable/Enable DIP-switch setting.
SW2 - FIBER FULL/HALF DUPLEX
Setting this DIP-switch to Half-Duplex “HDX” facilitates a connection that supports
Management Options iConverter, Serial Agent
Network Management
1: Chassis and Module Management
2: Set Module Name Preferences
Management Module Preferences
3: IP and Control Preferences
4: SNMP Preferences
5: Abandon Preference Changes
6: Save Preference Changes
7: Restore Factory Defaults
8: Restart Management Module
9: Other Networking Features
Management Module Maintenance
10: Firmware Update
11: Set Date/Time
IP Address = 192.168.1.220
Chassis Number = 1
Enter Choice, <H>elp, E<x>it >
Figure C: Command Line Interface Menu Options
The CLI interface allows for the detailed configuration of the module. It is recommended
to configure the module with an IP address associated with the attached network.
Also, SNMP traphost address should be configured if the module is managed with an
SNMP-based Management System. See the 10/100M2 User Manual for complete
information.
4) VERIFY OPERATION
Once the module has been installed
and configured per steps 1 - 3, verify
the module is operational by viewing
the LED indicators.
The Power LED indicates the
module is receiving power.
The Fiber Optic link LED indicates
the fiber optic connection has been
established. Verify the Link Mode
selection is set to Link Segment
(LS). Until a stable link is
established, leave the Link Mode
configured for LS. After a Link
presence is established, the Link
Mode selection can be modified.
The UTP link LED indicates the
module has established a
connection across its UTP port.
LED
Function
"Legend"
Color Off State On / Blinking State
Power "Pwr" Green No power On: Module has power
Network Ports Status*
100Mbps
Fiber Optics
"FO" Green No Fiber Link
On: Fiber link is active
Blinking: Fiber Data Activity
UTP port 10
Mbps "10"
Green
10Mbps not
active
On: 10Mbps mode selected
and the UTP link is active
Blinking: UTP Data Activity
UTP port
100 Mbps
"100"
Green
100Mbps not
active
On: 100Mbps mode selected
and UTP link is active
Blinking: UTP Data Activity
UTP port
Full-Duplex
"FDX"
Green
Half-Duplex
when UTP link
is active
On: Full-Duplex and UTP link
is active
*Review Link Modes section for other LED display patterns
Figure D: LED Indicators
Form 040-8900N-001 B
Omnitron Systems Technology * 140 Technology Dr. #500 * Irvine, CA 92618
949.250.6510 tel * 949.250.6514 fax * www.omnitron-systems.com
SW1 SW8
Up
Down
Bank 1
Figure A: DIP-Switch Location