Omnitron Systems Technology iConverter 2GXM2 Plugin Module - Manual

iConverter 2GXM2 Plug-in Module QUICK START GUIDE
The Omnitron iConverter ® 2GXM2 Network Interface Device
(NID) with integrated management provides Gigabit Ethernet
(1000BASE-X) SFP fiber-to-fiber media conversion.
The 2GXM2 conforms to Ethernet in the First Mile (EFM) fiber
standards to support Fiber-to-the-X (FTTX) in Metropolitan and
Enterprise LAN networks. Built-in Operation, Administration
and Maintenance (OAM) functionality enables the 2GXM2
to operate as a managed demarcation point at the customer
premises and network edge, offering Quality of Service
capability.
The 2GXM2 module can be managed using Omnitron’s
NetOutlook TM SNMP Management Software, third-party SNMP
Client, Telnet or the Command Line Interface (CLI).
For more information, including the complete User Manual on the 2GXM2 Plug-in
module, access Omnitron’s documentation download web page to view all relevant
documents:
http://www.omnitron-systems.com/downloads.php
IMPORTANT
The firmware of the Network Management Module (NMM or NMM2) and
NetOutlook must be the same or greater than the firmware on the 2GXM2 for
the module to be managed.
INSTAllATION PROCEDURE
1) Configure DIP-Switches
2) Install Module in Chassis and Connect
Cables
3) Configure Module via Command Line
Interface
4) Verify Operation
1) CONFIGURE DIP-SwITChES
DIP-SwITCh BaNk 1
Sw1, Sw2 - aUTO/MaNUal NEGOTIaTION
“aN/MaN”
When the DIP-switch is in the LEFT Auto-
Negotiate “AN” position (factory default), the Port
automatically determine the duplex and pause
modes of the connecting fiber optic devices. If
the connecting fiber optic devices cannot provide the proper signal to indicate their own
mode of operation, the DIP-switch should be set to the RIGHT Manual “MAN” position.
See Figure B on page 2 for more information.
NOTE: when Port 1 operates in auto-Negotiation mode, the port advertises for
Pause. when the Fiber optic ports (Port 1 and Port 2) operates in Manual mode,
Pause is not advertised.
Management Options iConverter, Serial Agent
Network Management
1: Chassis and Module Management
2: Set Module Name Preferences
Management Module Preferences
3: IP and Control Preferences
4: SNMP Preferences
5: Abandon Preference Changes
6: Save Preference Changes
7: Restore Factory Defaults
8: Restart Management Module
9: Other Networking Features
Management Module Maintenance
10: Firmware Update
11: Set Date/Time
IP Address = 192.168.1.220
Chassis Number = 1
Enter Choice, <H>elp, E<x>it >
Figure D: Command Line Interface Menu Options
The CLI interface allows for the detailed configuration of the module. It is recommended
to configure the module with an IP address associated with the attached network. Also,
SNMP traphost address should be configured if the module is managed with an SNMP-
based Management System. See the 2GXM2 User Manual for complete information.
4) VERIFy OPERaTION
Once the module has been installed and configured per steps 1 - 3, verify the module
is operational by viewing the
LED indicators.
The Power LED indicates the
module is receiving power
from the chassis.
The Fiber Optic link LEDs
indicate the fiber optic
connections have been
established. Verify the Link
Mode selection is set to Link
Segment (LS). Until a stable
link is established, leave the
Link Mode configured for LS.
After a Link presence is established,
the Link Mode selection can be modified.
Page 4
Switch 1
Switch 4
LEFT
Switch 1
Switch 8
Bank 2
Bank 1
RIGHT
Figure A: DIP-Switch Locations
Form 040-8980N-002 C 7/10
Omnitron Systems Technology * 140 Technology Dr. #500 * Irvine, CA 92618
949.250.6510 tel * 949.250.6514 fax * www.omnitron-systems.com
Page 1
lED Function
“legend”
Color Off State On / Blinking State
Power “Pwr” Green No Power On: Module has power
Power Supply
Status #X
Green
Chassis Power
Supply not installed
On: Power available from
installed Power Supply #X
Blinking: No power available
from installed Power Supply #X
Port 1
Fiber Link Activity
“P1”
Green No Fiber Link
On: Fiber link is active
Blinking: Fiber Data Activity
Chassis Management
Master/Slave
“Msr/Slv”
Green Chassis Slave
Mode
On: Chassis Master
Blinking: Operating in OAM
Mode
Port 2
Fiber Link Activity
“P2”
Green No Fiber Link
On: Fiber link is active
Blinking: Fiber Data Activity
Figure E: LED Indicators