Document Outline

• TWO YEAR LIMITED WARRANTY
• Safety Precautions
• 1 Introduction
  • 1.1 About This Manual
    • Target Audience
    • If You Have Comments About This Manual...
    • Textual and Graphic Conventions
      • Text Conventions
      • Graphic Conventions
  • 1.2 Using This Manual
  • 1.3 Description, Features and Benefits
    • Key Features and Benefits
    • Parts List
      • Optional Accessories
• 2 Controls and Functions
  • 2.1 Vision 10/12 at a Glance
    • Front/Top/Side View
      • Figure 2-1 . Vision 10/12 Top/Front/Side View
    • Rear/Top/Side View
      • Figure 2-2 . Vision 10/12 Rear/Top/Side View
  • 2.2 Vision 10/12 Remote Control
    • Figure 2-3 . Vision 10/12 Remote Control
• 3 Installation
  • 3.1 Remote Control
    • Notes on Batteries
    • Notes on Remote Control Operation
      • Figure 3-1 . Available Range of the Remote Control
  • 3.2 Quick Setup
    • Table 3-1 . Installation Overview
  • 3.3 Installation Considerations
    • Installation Type
      • Table 3-2 . Projector Installation Options
    • Ambient Light
    • Other Considerations
    • Throw Distance
      • Figure 3-2 . Estimating Throw Distance
    • Vertical and Horizontal Position
      • Figure 3-3 . Projector Placement
    • Vertical and Horizontal Lens Shift
      • Figure 3-4 . Vertical Lens Shift (Example only)
      • Figure 3-5 . Horizontal Lens Shift (Example only)
      • Table 3-3 . Vertical and Horizontal Lens Shift Limits
    • Adjusting the Projection Angle
    • Mounting
      • Floor Mounting
      • Ceiling Mounting
    • Folded Optics
      • Figure 3-6 . Folded Optics
  • 3.4 Connections to the Vision 10/12
    • Connector Panel Access
    • Connecting the Vision 10/12 to Source Components
      • HDMI Connections
        • Figure 3-7 . HDMI (or DVI) Source Connections
      • RGB-HD Connections
        • Figure 3-8 . Analog RGB Connections
      • Component Video Connections
        • Figure 3-9 . Component Video Connections
      • Composite/S-Video Connections
        • Figure 3-10 . Composite and S-Video Connections
    • RS-232 Controller Connection
      • Figure 3-11 . RS-232 Control System Connection
    • Connecting to the 12-Volt Trigger Output
      • Figure 3-12 . Connecting the 12-Volt Trigger Output
• 4 Operation
  • 4.1 Turning on the Power
  • 4.2 Adjusting the Projector Height or Projection Angle
    • Figure 4-1 . Adjusting the Feet
  • 4.3 Changing the OSD Language
  • 4.4 Adjusting the Picture Orientation
  • 4.5 Lens Adjustments
    • Focus/Zoom
      • Figure 4-2 . Focus and Zoom Controls
    • Shift
      • Figure 4-3 . Vertical and Horizontal Lens Shift Controls
  • 4.6 Using the On-Screen Menus
    • Figure 4-4 . Vision 10/12 OSD Menu Structure
    • Main Menu
    • Source Select
    • Aspect Ratio
      • Table 4-1 . Aspect Ratio Settings
    • Picture Adjust
      • Brightness
        • Figure 4-5 . Typical PLUGE Pattern for Adjusting Brightness
      • Contrast
        • Figure 4-6 . Typical Gray Bar Pattern for Adjusting Contrast
      • Color Saturation
        • Figure 4-7 . Typical Color Bar Pattern for Adjusting Color Saturation and Tint
      • Tint
      • Sharpness
        • Figure 4-8 . Typical Test Pattern for Adjusting Sharpness
      • Gamma
      • Color Temperature
        • Table 4-2 . Effect of X and Y Coordinates for Color Temperature
        • Figure 4-9 . CIE 1931 Chromaticity Diagram
      • ICC Select
      • White Balance
      • Save Settings
      • Load Saved Settings
    • Image Option
      • HD/RGB Adjust
      • Image Position
      • Over Scan Adjust
      • SDTV Adjust
      • Brightness Enhance
      • Lamp Power
      • Information
      • Restore Factory Settings
    • Installation
      • Language
      • Picture Configuration
      • OSD Timeout
      • OSD Transparent
      • Source Detect
      • Auto Power Off
      • Blue Enable
      • OSD Position
      • Keystone Correction
        • Figure 4-10 . Horizonal and Vertical Keystone Correction
      • Fan High Speed Mode
    • ISF Settings
      • Brightness
      • Contrast
      • Color
      • Tint
      • Sharpness
      • Gamma
      • Color Temp
      • Load Saved Settings
      • White Balance
      • Save Settings
      • Lamp Timer Reset
      • ICC Adjust
      • ISF Enable
        • Figure 4-11 . ISF-Enabled Vision 10/12 Splash Screen
      • Blue Enable
      • Splash Screen Timer
      • Noise Reduction
• 5 Maintenance and Troubleshooting
  • 5.1 Cleaning the Projector
  • 5.2 Cleaning the Lens
  • 5.3 Cleaning the Intake and Exhaust Vents
  • 5.4 Lamp Maintenance
  • 5.5 Lamp Cautions
  • 5.6 Lamp Replacement
  • 5.7 Troubleshooting Tips
    • Table 5-1 . Troubleshooting Chart
• 6 Serial Communications
  • 6.1 RS-232 Connection and Port Configuration
  • 6.2 Serial Command Syntax
    • Table 6-1 . Serial Commands
• 7 Specifications
  • 7.1 Vision 10/12 Specifications
    • Table 7-1 . Vision 10/12 Specifications
  • 7.2 Vision 10/12 Dimensions
    • Figure 7-1 . Vision 10/12 Dimensions
  • 7.3 Computer Signal Compatibility
    • Table 7-2 . Computer Signal Compatibility Chart
  • 7.4 Video Signal Compatibility
    • Table 7-3 . Video Signal Compatibility Chart