Yamaha DM2000 - Manual (Page 207)

Punching In & Out Individual Parameters
207
DM2000 Version 2—Owner’s Manual
Punching In & Out Individual Parameters
During Automix rerecording, channels can be punched in and out by pressing the channel
strip [AUTO] buttons. Individual parameters can be punched in and out as follows.
Parameter Channel
OVER-
WRITE
Operation Punch In Punch Out
Channel Levels
(faders)
Input
FADER
Set Layer to input, Fader mode to
Fader Touch fader knob and
adjust 1
1. TOUCH SENSE on Fader Edit page must be TOUCH or LATCH.
Release fader knob 2
2. TOUCH SENSE on Fader Edit page must be TOUCH.
Bus Out, Aux
Send, Matrix
Send Set Layer to Master, Fader mode
to fader
Stereo Out Stereo Out fader
Group Master
faders
Set the Fader mode to Fader; Set
the Group Master in the User
Assignable Layer.
Pan Input PAN
Set Layer to input, Encoder mode
to Pan Press Encoder and
adjust Press Encoder
Surround Pan Input SURR
Select Input Layer and assign Sur-
round LFE Level or Surround Pan
Wheel to the Encoders Press Encoder and
adjust Press Encoder
EQ (F, Q, G)
All channels EQ
Turn on Auto EQ Edit In prefer-
ence (see page 277). Use
SELECTED CHANNEL EQUALIZER
section (If EQ parameter assigned
to an Encoder, also use Encoders) Adjust control Press [AUTO] button
EQ On/Off
Press EQ [ON] button Press [AUTO] button
Aux send 1–12 Input AUX
Set Layer to input, Fader mode to
Aux/Mtrx Touch fader knob and
adjust 1
Release fader knob 2
Set Layer to input, Encoder mode
to Aux/Mtrx (Or use SELECTED
CHANNEL AUX/MATRIX SEND
LEVEL controls) Press Encoder and
adjust Press Encoder
Aux send 1–12
mutes
Input
AUX
ON
Set Layer to input Press SELECTED CHAN-
NEL AUX/ MATRIX
SEND [ON] button 1
Press [AUTO] button
2
Matrix send 1–4
levels
Bus Out, Aux
Send, Stereo
Out
AUX
Set Layer to Master, Fader mode
to Aux/Mtrx Touch fader knob and
adjust 3
3. Cannot be used to control Stereo Out to Matrix Send levels.
Release fader knob 1
Set Layer to Master, Encoder
mode to Aux/Mtrx (Also use
SELECTED CHANNEL AUX/
MATRIX SEND LEVEL controls) Press Encoder and
adjust Press Encoder
Matrix send 1–4
mutes
Bus Out, Aux
Send, Stereo
Out
AUX
ON
Set Layer to master Press SELECTED CHAN-
NEL AUX/ MATRIX
SEND [ON] button
1
Press [AUTO] button
2
Effect parameters
(certain
parameters)
Effects proces-
sors 1–8
—
Select internal effects processors Push Parameter 1–4
control, or select the
parameters on the
Effect Edit page, then
press [ENTER] Push Parameter 1–4
control, or select the
parameters on the
Effect Edit page, then
press [ENTER]
User Defined
Plug-Ins
(parameters 1–4)
Plug-Ins 1–8 —
Select Plug-Ins Push Parameter 1–4
control. Select the
desired parameter on
the Plug-in Edit page,
then press [ENTER] Push Parameter 1–4
control. Select the
desired parameter on
the Plug-in Edit page,
then press [ENTER]
User Defined
Remote Layers
Faders FADER
Select User Defined Remote Layer Touch fader knob and
adjust 1
Release fader knob 2
Encoders PAN
Select User Defined Remote Layer Press Encoder and
adjust
Press Encoder