Zenith H20H52DT - Manual (Page 34)

Page 34
Installer Menu Item 4-I through 13-I: Detailed Descriptions.
Installer Menus
If some channels were not found by AUTO
PROGRAM, select the appropriate AFC setting
here and add the channels using the ADD/DEL
option in the Setup Menu.
4-I. STRT CHANNEL (Start Channel)
When active, this function allows you to
determine the initial channel number when the
TV is turned ON. This feature is useful for an in-
house information channel, since the TV would
always select that channel when it is turned on.
Setting this to 255 causes the last channel
viewed when TV was turned off to be the tuned to
channel when the TV is turned on again.
The range of values is 0 - 255. Use (adjust) keys
to choose numbers that determine the start
channel.
5-I. CHAN LOCK (Channel Lock)
CHAN LOCK is ideal if a cable box (or similar) is
the sole source for programming—and the TV
must always be on the same channel. Changing
channels with Channel Up/Down or keypad
numbers is impossible. Channel Lock is inactive
when set to 0 (default).
Generally, this feature is used in conjunction with
START CHANNEL (line 4-I.) where the start
channel may, for example, be set to 3 or 4. If the
start channel is 3 then the TV will remain on
channel 3.
NOTE: When CHANNEL LOCK is active and
CHANNEL OVERIDE is disabled, AUTO
PROGRAM is not active.
6-I. GHOST CH (Ghost Channel)
When set to 1, the current channel number is
displayed in the upper right corner of the display.
The number moves slightly to prevent damage to
the screen. The default is “0” or OFF.
NOTE: When captions are on, the “ghost
channel” is not displayed.
7-I. START VOLUME
This function allows the Installer to determine the
initial volume level setting when the TV is turned
ON. This feature is useful for an in-house
information channel, since the TV would always
select that volume level when it is turned on. The
range of values are 0- 63, 255. If 255 is selected,
the current volume level will be retained in
memory when the TV is turned off; at TV turn on,
volume level is automatically set to the previous
or last level.
8-I. MIN VOLUME (Minimum Volume)
This function determines the minimum volume
level allowable with the VOLUME (VOL)
Up/Down control. In this way, for example,
someone cannot set the volume too low to hear.
The range is from 0 to 63—change values with
ADJUST. The factory default is 0, which provides
full range of volume control. It may be best to set
the same value on every TV.
NOTE: The minimum volume level cannot have a
value setting higher than in the MAX VOLUME
level (described below).
9-I. MAX VOLUME (Maximum Volume)
This function determines the maximum volume
level allowable with the VOLUME VOL Up/Down
control. In this way, for example, someone cannot
set the volume level high enough to disturb
others.
The range is 0 to 63, with 63 as the default which
gives the user the full range of volume control.
Change values with ADJUST keys. It may be
best to set the same value on every TV.
NOTE: The maximum volume level cannot have
a value setting lower than the MIN VOLUME level
(described previously).
10-I. MUTE DISABLE
Enables or disables sound mute function. When
set to 1, sound cannot be muted. When set to 0,
sound can be muted.
11 KEY DEFEAT (Keyboard Defeat)
When set to 1, it prevents the end user from
accessing screen menus on the front
panel—MENU, SELECT, and ADJUST do not
function. When set to 0, those keys are
functional. The menus can always be accessed
with MENU on the remote.
12-I. IR BANKS EN.
For direct access to a particular Channel Bank.
When enabled, installer can access a channel
bank by inputting the IR code for the bank.
13-I. SCAN MODE
Allows variation in setting the On/Off with
Channel UP/DOWN.
You may opt for TV channels only; TV channels +
Off/ON; TV channels + FM radio; TV channels +
FM radio + Off/On with these settings
for Scan Mode: