Vitek VT-1510 SR - Manual (Page 8)

8
ENGLISH
Attention! Water is hot. Be careful.
Note:
- During water boiling the pump switches
on periodically, it is normal.
- To switch to the “ESPRESSO” mode from
the “CAPPUCCINO” mode or the “WATER
BOILING” mode, press the On/Off (14)
button once.
AUTO-OFF button
If you have not been using the coffee mak-
er for 1 hour, it will switch off automatical-
ly. You can switch on the coffee maker by
pressing the On/Off (14) button.
SCALE REMOVAL
When you see the flashing (25) indication
on the display (6) you should perform scale
removal in the heating element of the cof-
fee maker using citric acid. While scale
removal, make sure not to damage the
tabletop with acids, be especially careful
if the tabletop is made of marble or stone.
Put a tissue, a dry cloth under the coffee
maker or place the coffee maker in the cor-
responding tray.
Note: The appearance of the (25) indica-
tion on the display (6) depends on water
hardness in your region and is about:
- HI-high water hardness – 30 liters
- MI- medium water hardness - 45 liters
- LO- low water hardness - 60 liters
When you see the flashing (25) indication
on the display (6), perform scale removal.
• Unplug the coffee maker and wait until it
cools down completely.
• Turn the filter holder to the left and re-
move it.
• Use a corresponding cross screwdriver
to remove the mounting screw (a), by
turning it clockwise, and remove the filter
– strainer (b) (pic.9).
• When there is scale deposit on the filter
(b), put the filter in citric acid solution,
and then wash it.
• Prepare citric acid solution: 2 teaspoons
of citric acid and 1 liter of water and pour
this solution in the water tank (9). Set the
tank (9) on its place.
• Select a corresponding bowl with capac-
ity not less than 0,6 l and put it on the wa-
ter tray grid (2) (1). Place the bowl in a
way that the cappuccinator tube (12) is in
the bowl.
• Insert the plug into the socket and press
the On/Off (14) button to switch on the
coffee maker.
• Wait until the coffee maker warms up, the
(29) indication will disappear.
• Press the (17), (19) buttons simultane-
ously, the pump will switch on and water
supply will start, the scale removal (26)
indication will be lighting, the heating el-
ement will switch on as well and the (29)
indication will light up.
• To wash the cappuccinator tube (12) sup-
ply steam, by turning the steam supply
handle (10) anti clockwise until bumping
for 8-10 sec. Stop steam supply, by turn-
ing the steam supply handle (10) clock-
wise until bumping.
• When about 0,5 l of water passes, the
pump will switch off and the coffee mak-
er will switch to the standby mode.
• Detach installed container, at that sound
signal is heard, and symbol (23) starts
blinking on display (6), pour water out of
container and put it again on the grill (2)
of water tray (1). Install the container thus
the cappuccinator-pipe (12) is inside it.
• Detach and clean water reservoir (9), fill it
with water up to maximal mark and install
it to the former place.
• Pump is on, and cleaning mode is start-
ed. In order to clean cappuccinator-pipe
(12), open steam supply by turning team
supply handle (10) clockwise up to stop
for 2-3 seconds.
• After completion of cleaning mode, cof-
fee machine is switched off automati-
cally.
1510.indd 8 1510.indd 8 02.04.2008 15:43:59 02.04.2008 15:43:59