Net Optics iTap 10_100_1000BaseT Port Aggregator - Manual (Page 4)

Features and Benefits
®
5303 Betsy Ross Drive • Santa Clara, CA 95054
+1 (408) 737-7777 • www.netoptics.com
Net Optics ® , Intelligent Tap TM , iTap TM , and iTap into your Network ® are trademarks of Net Optics, Inc.
Copyright 2010 Net Optics, Inc. All rights reserved. Revised 03/09
OpenView is a registered trademark of the Hewlett-Packard Company. Tivoli is a registered trademark of the IBM Corporation.
Specifications
Copper
Input: 100-240 VAC, 0.5A, 47-63Hz
Output: 12V, 3A
Cable Type: 22-24 AWG Unshielded, CAT5E
Connectors: RJ45, 8-pin Connectors
Electrical
Power Supply Input: 100-240VAC, 0.5A, 47-63Hz
Output: 12V, 3A
Memory
1GB buffer
Environmental
Operating Temperature: 0˚C to 40˚C
Storage Temperature: -10˚C to 70˚C
Relative Humidity: 10% min, 95% max,
non-condensing
Mechanical
Dimensions: 1.125” high x 11” deep x 8.5” wide
Indicators
(1) 2x16 LCD
(3) Link LEDs
(2) Threshold Alarm LEDs
(2) Power LEDS
Software
Command Line Interface (CLI): Any terminal
emulation software
Net Optics Web Manager: Any browser
Net Optics System Manager: Windows 98,
Windows 2000, Windows XP
Wireless Option
Standard: Conforms to IEEE 802.11b, 11 Mbps
Indoor Range (typical): 50 feet
Outdoor Range: 100 feet
Available Base Models
10/100/1000BaseT Copper
Certifications
Fully RoHS compliant
Part Number
IPA- CU3
IPA- CU3-AR
Certifications
Fully RoHS compliant
Front Panel Display and LEDs Real-time utilization and peak traffic information displayed on the front panel saves you time and money spent using other tools to get basic information.
Alarm LEDs indicate if traffic levels have exceeded a set threshold, allowing you to respond quickly to changing traffic conditions.
Net Optics Web Manager Without any specialized software, you can access the traffic information monitored by any iTap Port Aggregator. All you need is a computer with a browser and
access to the IP address of the iTap Port Aggregator. No matter where you are, you can control your iTap Port Aggregator and monitor traffic information.
Net Optics System Manager Net Optics’ SNMP management tool, System Manager, gives you single-point control and visibility into any link in the network with an iTap Port Aggregator
anywhere in the world. Distributed on strategic links, iTap Port Aggregators provide baseline information and early warning alarms to help you deploy your
security and monitoring devices more effectively over more links.
Command Line Interface The password-protected command line interface gives you complete access to all of iTap Port Aggregator’s functionality via an RS232 port. Most importantly,
you can use the CLI to disable the Management Port and prevent the front panel display from showing traffic information.
Net Optics Management
Information Base (MIB) Use the iTap Port Aggregator with your current SNMP management tool. Net Optics’ MIB and SNMP traps are completely compatible with popular SNMP tools
such as OpenView and Tivoli
® .
Aggregation Net Optics’ proven port aggregation technology allows you to monitor traffic using a single NIC on your monitoring device. Unlike any other port aggregator
tap, the iTap Port Aggregator monitors utilization levels of both sides of the full-duplex link so this information is not lost. 512MB traffic buffers help ensure
that your monitoring device does not miss traffic during bursts.
Half-duplex (Tap) Mode Use the iTap Port Aggregator as a conventional half-duplex network Tap to capture all traffic when aggregated utilization exceeds 100 percent of a monitor port’s
bandwidth.
Port Ordering Ensure that packets appear on the monitor ports in the same time sequence they arrived at the network ports by enabling the Port Ordering feature.
Timestamping For precise timing analysis, replace the CRC bytes of each packet with an 8 nanosecond resolution timestamp.
Cables Included All cables required for installation are included. Follow the connection diagram on top of the iTap Port Aggregator and you are halfway done with the
installation of your iTap Port Aggregator.