Asus TS500-E2 - Manual (Page 85)

4 - 5 4 - 5 4 - 5 4 - 5 4 - 5 A S U S T S 5 0 0 - E 2 A S U S T S 5 0 0 - E 2 A S U S T S 5 0 0 - E 2 A S U S T S 5 0 0 - E 2 A S U S T S 5 0 0 - E 2
3 . 3 . 3 . 3 . 3 . U S B d e v i c e w a k e - u p ( 3 - p i n U S B P W 1 2 , U S B P W 3 4 ) U S B d e v i c e w a k e - u p ( 3 - p i n U S B P W 1 2 , U S B P W 3 4 ) U S B d e v i c e w a k e - u p ( 3 - p i n U S B P W 1 2 , U S B P W 3 4 ) U S B d e v i c e w a k e - u p ( 3 - p i n U S B P W 1 2 , U S B P W 3 4 ) U S B d e v i c e w a k e - u p ( 3 - p i n U S B P W 1 2 , U S B P W 3 4 )
Set these jumpers to +5V to wake up the computer from S1 sleep mode
(CPU stopped, DRAM refreshed, system running in low power mode)
using the connected USB devices. Set to +5VSB to wake up from S4
sleep mode (no power to CPU, DRAM in slow refresh, power supply in
reduced power mode).
• The USB device wake-up feature requires a power supply that can
provide 500mA on the +5VSB lead for each USB port; otherwise, the
system would not power up.
• If you are using Windows 2000, you need to install Service Pack 4 to
wake up the system from S4 sleep mode.
• The total current consumed must NOT exceed the power supply
capability (+5VSB) whether under normal condition or in sleep mode.
2 . 2 . 2 . 2 . 2 . C P U f a n p i n s e l e c t i o n ( 3 - p i n F M _ C P U 1 , F M _ C P U 2 ) C P U f a n p i n s e l e c t i o n ( 3 - p i n F M _ C P U 1 , F M _ C P U 2 ) C P U f a n p i n s e l e c t i o n ( 3 - p i n F M _ C P U 1 , F M _ C P U 2 ) C P U f a n p i n s e l e c t i o n ( 3 - p i n F M _ C P U 1 , F M _ C P U 2 ) C P U f a n p i n s e l e c t i o n ( 3 - p i n F M _ C P U 1 , F M _ C P U 2 )
These jumpers allow you to connect either a 3-pin or a 4-pin fan cable
plug to the CPU fan connectors (CPU_FAN1, CPU_FAN2). Set these
jumpers to pins 1-2 if you are using a 3-pin fan cable plug, or to pins 2-3
if you are using a 4-pin plug.
NCLV-DS2 FM_CPU Setting
FM_CPU2
FM_CPU1
DC mode PWM
(Default)
1 2 2 3
3 2 2 1
DC mode PWM
(Default)
NCLV-DS2
NCLV-DS2 USB device wake-up
USBPW12
(Default)
+5V +5VSB
1 2 2 3
USBPW34
(Default)
+5V +5VSB
1 2 2 3