Asus RS260-E3/RS8 - Manual (Page 76)

C h a p t e r 4 : M o t h e r b o a r d i n f o r m a t i o n C h a p t e r 4 : M o t h e r b o a r d i n f o r m a t i o n C h a p t e r 4 : M o t h e r b o a r d i n f o r m a t i o n C h a p t e r 4 : M o t h e r b o a r d i n f o r m a t i o n C h a p t e r 4 : M o t h e r b o a r d i n f o r m a t i o n 4 - 1 2 4 - 1 2 4 - 1 2 4 - 1 2 4 - 1 2
3 . 3 . 3 . 3 . 3 . P r i m a r y I D E c o n n e c t o r s ( 4 0 - 1 p i n P R I _ I D E , S E C _ I D E ) P r i m a r y I D E c o n n e c t o r s ( 4 0 - 1 p i n P R I _ I D E , S E C _ I D E ) P r i m a r y I D E c o n n e c t o r s ( 4 0 - 1 p i n P R I _ I D E , S E C _ I D E ) P r i m a r y I D E c o n n e c t o r s ( 4 0 - 1 p i n P R I _ I D E , S E C _ I D E ) P r i m a r y I D E c o n n e c t o r s ( 4 0 - 1 p i n P R I _ I D E , S E C _ I D E )
These connectors are for an Ultra DMA 100/66 signal cable. The Ultra
DMA 100/66 signal cable has three connectors: a blue connector for the
primary IDE connector on the motherboard, a black connector for an Ultra
DMA 100/66 IDE slave device (optical drive/hard disk drive), and a gray
connector for an Ultra DMA 100/66 IDE master device (hard disk drive). If
you install two hard disk drives, you must configure the second drive as a
slave device by setting its jumper accordingly. Refer to the hard disk
documentation for the jumper settings.
• Pin 20 on the IDE connector is removed to match the covered hole on
the Ultra DMA cable connector. This prevents incorrect insertion when
you connect the IDE cable.
• Use the 80-conductor IDE cable for Ultra DMA 100/66 IDE devices.
®
PVL-D/2U/SCSI
PVL-D/2U/SCSI IDE connectors
NOTE: Orient the red markings
(usually zigzag) on the IDE
ribbon cable to PIN 1.
SEC_IDE
PRI_IDE
PIN 1
PIN 1
4 . 4 . 4 . 4 . 4 . P o w e r s u p p l y S M B u s c o n n e c t o r ( 5 - p i n P S U S M B 1 ) P o w e r s u p p l y S M B u s c o n n e c t o r ( 5 - p i n P S U S M B 1 ) P o w e r s u p p l y S M B u s c o n n e c t o r ( 5 - p i n P S U S M B 1 ) P o w e r s u p p l y S M B u s c o n n e c t o r ( 5 - p i n P S U S M B 1 ) P o w e r s u p p l y S M B u s c o n n e c t o r ( 5 - p i n P S U S M B 1 )
This connector is for the power supply SMB cable, if your power supply
supports the SMBus function.
®
PVL-D/2U/SCSI
PVL-D/2U/SCSI Power supply SMBus connector
PSUSMB1
+3.3V Remote Sense GND NC I2C_7_DA
T
A
#
I2C_7_CLK#