Extron Electronics PowerCage FOX SR HDMI User Guide - Manual (Page 23)

Command and response table for SIS commands (continued)
PowerCage FOX SR HDMI Scaling Receiver • Remote Control 17
Command ASCII Command
(host to unit)
Response
(unit to host)
Additional description
Output scaler rate
Set the output rate EX& Rate } Rate X&] Select the output resolution and rate to X& ( see the
table below the Show command).
Show the output rate E Rate } X&] See the table below.
X& Source or value X& Source or value X& Source or value X& Source or value X& Source or value
10 640x480 @ 50 Hz 11 640x480 @ 60 Hz 12 640x480 @ 75 Hz 13 800x600 @ 50 Hz 14 800x600 @ 60 Hz
15 800x600 @ 75 Hz 16 852x480 @ 50 Hz 17 852x480 @ 17 Hz 18 852x480 @ 75 Hz 19 1024x768 @ 50 Hz
20 1024x768 @ 60 Hz 21 1024x768 @ 75 Hz 22 1024x852 @ 50 Hz 23 1024x852 @ 60 Hz 24 1024x852 @ 75 Hz
25 1024x1024 @ 50 Hz 26 1024x1024 @ 60 Hz 27 1024x1024 @ 75 Hz 28 1280x768 @ 50 Hz 29 1280x768 @ 60 Hz
30 1280x768 @ 75 Hz 31 1280x800 @ 50 Hz 32 1280x800 @ 60 Hz 33 1280x800 @ 75 Hz 34 1280x1024 @ 50 Hz
35 1280x1024 @ 60 Hz 36 1280x1024 @ 75 Hz 37 1360x765 @ 50 Hz 38 1360x765 @ 60 Hz 39 1360x765 @ 75 Hz
40 1360x768 @ 50 Hz 41 1360x768 @ 60 Hz 42 1360x768 @ 75 Hz 43 1365x768 @ 50 Hz 44 1365x768 @ 60 Hz
45 1365x768 @ 75 Hz 46 1366x768 @ 50 Hz 47 1366x768 @ 60 Hz 48 1366x768 @ 75 Hz 49 1365x1024 @ 50 Hz
50 1365x1024 @ 60 Hz 51 1365x1024 @ 75 Hz 52 1440x900 @ 50 Hz 53 1440x900 @ 60 Hz 54 1440x900 @ 75 Hz
55 1400x1050 @ 55 Hz 56 1400x1050 @ 60 Hz 57 1680x1050 @ 50 Hz 58 1680x1050 @ 60 Hz 59 1600x1200 @ 50 Hz
60 1600x1200 @ 60 Hz 61 1920x1200 @ 50 Hz 62 1920x1200 @ 60 Hz 63
480p @ 59.94 Hz 64 480p @ 60 Hz
65 576p @ 50 Hz 66 720p @ 25 Hz 67 720p @ 29.97 Hz 68 720p @ 30 Hz 69 720p @ 50 Hz
70 720p @ 59.94 Hz 71 720p @ 60 Hz 72 1080i @ 50 Hz 73 1080i @ 59.94 Hz 74 1080i @ 60 Hz
75 1080p @ 23.98 Hz 76 1080p @ 24 Hz 77 1080p @ 25 Hz 78 1080p @ 29.97 Hz 79 1080p @ 30 Hz
80 1080p @ 50 Hz 81 1080p @ 59.94 Hz 82 1080p @ 60 Hz 83 2048x1080
@ 23.98 hz
84 2048x1080 @ 24 Hz
85 2048x1080 @ 25 Hz 86 2048x1080
@ 29.97 Hz
87 2048x1080 @ 30 Hz 88 2048x1080 @ 50 Hz 89 2048x1080
@ 59.94 Hz
90 2048x1080 @ 60 Hz
HDMI output format
Set the output format EX* Vtpo } Vtpo X*] Set the video output format (color space).
Show the output format E Vtpo } X*]
Screen saver (active when there is no active video)
Set screen saver mode E M X( Ssav } SsavM X(]
View screen saver mode E MSsav } X(]
Set timeout duration E T X1) Ssav } Ssav X1)]
View timeout duration E TSsav } X1)]
VIew screen saver status E SSsav } X1!]
Freeze
NOTE: The receiver unfreezes, returning to motion video, when the screen saver starts, when you cycle receiver power, and when you
perform a reset.
Freeze the output 1F Frz1 ] Freeze the output (still video output).
Unfreeze the output 0F Frz0 ] Unfreeze the output (output motion video).
Show the freeze status F X1@]
NOTE: X& = Scaler resolution (EDID) See the table beneath the Output Scaler Rate commands, above.
X* = HDMI output format 0 = Auto (HDMI-RGB 444 or DVI-RGB 444) 4 = YUV 444 Full
1 = DVI RGB 444 5 = YUV 444 Limited
2 = RGB 444 6 = YUV 422 Full
3 = RGB Limited 7 = YUV 422 Limited
X( = Screen saver mode 1 = Black screen (default) 2 = Blue screen with on-screen display text
X1) = Screen saver timeout 000 = No screen saver 001 to 500 (seconds)
501 = Never timeout (default)
X1! = Screen saver status 0 = Input active, timer not running 2 = No active input, output sync disabled
1 = No active input, timer running
X1@ = Freeze status 0 = off (video in motion) 1 = on (video frozen)