Climax BB8000 PORTABLE LINE BORING MACHINE - Manual (Page 8)

8 11/06
NO. DESCRIPTION
Model BB8000 Components
25477 Motor, hydraulic - 14.3 in 3
(234.5 cm 3 ), 272 motor rpm,
2880 ft-lb (453 N•m) bar torque,
13.5 bar rpm
25478 Motor, hydraulic - 17.9 in 3
(293.6 cm 3 ), 261 motor rpm,
3630 ft-lb (573 N•m) bar torque,
10.8 bar rpm
25587 Hydraulic motor fitting kit - 3/4"
fittings
Kit includes fittings needed to con-
nect any hydraulic motor listed above
to hydraulic power units with hoses
that have 3/4" female quick discon-
nect fittings. Fittings are included
with every Climax hydraulic power
unit.
End-mount self-aligning bearing
support assembly (with spider)
Support assembly mounts to the end
of the work piece through a slotted
spider. Bar is held in place by a
self-aligning bearing. Center the bar
with the four adjusting screws. Two
bearing assemblies are required to
adequately support the bar. Support
assemblies may be different styles.
Special spiders are available upon
request.
21353 6" End-mount self-aligning bearing
support assembly (with spider)
23550 8" End-mount self-aligning bearing
support assembly (with support)
NO. DESCRIPTION
18556 Mechanical axial feed assembly
- 6" diameter boring bar
Assembly mounts to either end of
the bar. Manual feed is adjustable
and reversible with a feed rate of
.003" to .025" (.076 to .635 mm) per
revolution. Includes incremental dial
for positioning.
23393 Mechanical axial feed assembly
- 8" diameter boring bar
Assembly mounts to either end of the
bar. Manual feed is adjustable and
reversible with a feed rate of .003" to
.040" (.076 to 1.016 mm) per revolu-
tion. Includes incremental dial for
positioning.
17299 Rotational drive assembly
Mounts anywhere along the bar.
Locking rings hold the assembly
securely to the bar. Includes torque
arms for stability. Fits both 6" and 8"
diameter bars. 6" bars require rota-
tional drive collet (P/N 17300). Uses
one or two hydraulic drive motors.
Cooling fans require 120V AC 50 or
60 Hz power.
17300 Rotational drive collet, 8" to 6"
diameter bar
Collet fits inside the rotational drive
assembly above to enable it to
be mounted to 6" diameter bars.
Includes collet and key.
Hydraulic drive motors
Reversible motors with SAE 2-bolt
mounting flange to mount to the rota-
tional drive housing. Motor ports are
7/8-14 SAE O-ring type.
Fittings are
included with the hydraulic power
unit. Bar rpm's are maximum at 20
gpm. (For 50 Hz power units, reduce
the bar rpm by 15%; torque at the bar
remains the same.) Torque ratings (at
the bar) are constant.
25474 Motor, hydraulic - 7.3 in 3
(119.7 cm 3 ), 520 motor rpm,
1490 ft-lb (234 N•m) bar torque,
26 bar rpm
25475 Motor, hydraulic - 8.9 in 3
(146.0 cm 3 ) 420 motor rpm,
1820 ft-lb (286 N•m) bar torque,
21 bar rpm
25476 Motor, hydraulic - 11.3 in 3
(185.3 cm 3 ), 340 motor rpm,
2312 ft-lb (366 N•m) bar torque,
17 bar rpm
Please note: Drawings may not
represent actual product.
11/06 9
NO. DESCRIPTION NO. DESCRIPTION
17436 Adapter sleeve, 8" (203.2 mm) to 6"
(152.4 mm) ID
Adapter allows 6" (152.4 mm) diam-
eter boring bars to use 8" (203.2 mm)
diameter spider and bearing support
assemblies.
Tool carrier
Split-design tool carrier mounts
anywhere along the boring bar. Car-
rier has built-in wipers to protect the
bar and carrier from dirt and chips.
Boring and facing heads mount to
the tool carrier with screws and, if
required, spacers. Carrier includes
brass nut and drive key.
34470 Tool carrier, 6" (152.4 mm) diameter
boring bar
34323 Tool carrier, 8" (203.2 mm) diameter
boring bar
Manual boring head assembly
Boring head mounts to either a 6"
or 8" tool carrier. Can bore 16" to
80" (406.4 to 2032.0 mm) diameters.
Assembly includes 1" (25.4 mm), 2"
(50.8 mm), 5" (127.0 mm), and 10"
(254.0 mm) spacers. Use the spacers
to set the desired boring diameter
range. Features micro-adjustable
tools for fine adjustments. Two tool
holders permit heavy boring. Holders
accept carbide inserts and chip
breakers.
This assembly requires
either 6" or 8" tool carrier (P/N
18535 or 18537).
21135 Manual boring head assembly,
16"-18" (406.4 - 457.2 mm) IDs
21136 Manual boring head assembly,
16"-20" (406.4 - 508.0 mm) IDs
21137 Manual boring head assembly,
16"-22" (406.4 - 558.8 mm) IDs
21138 Manual boring head assembly,
16"-24" (406.4 - 609.6 mm) IDs
21139 Manual boring head assembly,
16"-26" (406.4 - 660.4 mm) IDs
21140 Manual boring head assembly,
16"-28" (406.4 - 711.2 mm) IDs
21141 Manual boring head assembly,
16"-30" (406.4 - 762.0 mm) IDs
21142 Manual boring head assembly,
16"-40" (406.4 - 1016.0 mm) IDs
21143 Manual boring head assembly,
16"-50" (406.4 - 1270.0 mm) IDs
21144 Manual boring head assembly,
16"-60" (406.4 - 1524.0 mm) IDs
21145 Manual boring head assembly,
16"-70" (406.4 - 1778.0 mm) IDs
21146 Manual boring head assembly,
16"-80" (406.4 - 2032.0 mm) IDs
25074 8" End-mount self-aligning bearing
assembly (without spider)
Bearing assembly provides 4-way
adjustable bar alignment. Assembly
is flange mounted to the customer's
support structure. Taper locking
adapter secures the bar inside the
bearing. This bearing assembly is
included with the 8" end-mount self-
aligning bearing support assembly
(P/N 23550). 6" diameter bars
require adapter sleeve (P/N 17436).
ID-mount non self-aligning bearing
support assembly (with spider)
Bar is held in non self-aligning
bearing with a taper locking adapter.
Center the bar by adjusting the four
jaws on the support spider. Jaws can
be adjusted from outside the bore.
6" diameter bars require adapter
sleeve (P/N 17436).
18572 ID-mount bearing support assy,
6" dia. bar: 20 - 27.5" (508.0 -
698.5 mm) ID)
8" dia. bar: 23 - 27.5" (584.2 -
698.5 mm) ID
18573 ID-mount bearing support assy,
6" dia. bar: 20 - 35" (508.0 -
889.0 mm) IDs
8" dia. bar: 23 - 35" (584.2 -
889.0 mm) IDs
18574 ID-mount bearing support assy,
6" dia. bar: 20 - 49.5" (508.0 -
1257.3 mm) IDs
8" dia. bar: 23 - 49.5" (584.2 -
1257.3 mm) IDs
18575 ID-mount bearing support assy,
6" dia. bar: 20 - 63.5" (508.0 -
1612.9 mm) IDs
8" dia. bar: 23 - 63.5" (584.2 -
1612.9 mm) IDs
18576 ID-mount bearing support assy,
6" dia. bar: 20 - 77" (508.0 -
1955.8 mm) IDs
8" dia. bar: 23 - 77" (584.2 -
1955.8 mm) IDs
18533 8" Non self-aligning bearing as-
sembly (without spider)
Bearing mounts to the customer's
support structure. Taper locking
adapter secures the bar inside the
bearing. Assembly includes housing
and mounting screws, taper locking
adapter, and bearing. This assembly
is included in ID-mount non self-
aligning bearing support assemblies
(P/N 18572, 18573, 18574, 18575,
and 18576).
6" diameter bars
require adapter sleeve (P/N 17436).
Model BB8000 Components