Analog Way Tetra-VIO - Manual (Page 36)

APPENDIX A / ANNEXE A TETRA VIO
A-4: COMMANDS AND RESPONSES TABLE A-4: TABLE DES COMMANDES ET RÉPONSES
COMMAND RESPONSE
COMMAND DESCRIPTION
TYPE
VALUE /VALEUR
COMMANDE RÉPONSE
DESCRIPTION DE LA COMMANDE MIN MAX DESCRIPTION
FRONT PANEL COMMANDS / COMMANDES DE LA FACE AVANT
IC IC Selected input. Rd 0 4 1 = INPUT #1 2 = INPUT #2
3 = INPUT #3 4 = INPUT AUX Ic Ic Input selection. Rd/Wr 0 4
RZ RZ Freeze. Rd/Wr 0 1 0 = inactive 1 = active.
RK RK Centering. Rd/Wr 0 1 1 = Centering (automatic reset).
Ia Ia Setup (auto setting) Rd/Wr 0 1 1 = Auto setting (automatic reset).
OB OB BLACK output screen selection. Rd/Wr 0 1 1 = BLACK.
wS wS Standby Rd/Wr 0 2 1 = set to standby mode 2 = wake up the device.
ws ws Standby mode status Rd 0 1 0 = standby inactive 1 = standby active
INPUT COMMANDS / COMMANDES D’ENTRÉE
Ia Ia Auto setting Rd/Wr 0 1 1 = Auto setting (automatic reset).
IP IP Input selection for adjustment. Rd/Wr 0 4 1 = INPUT #1 2 = INPUT #2
3 = INPUT #3 4 = INPUT AUX Ip Ip Selected input for adjustment. Rd 0 4
IU IU Enabled Input (according to IP). Rd/Wr 0 1 0 = Input unused 1 = Input used
IT IT
Input signal type selection. (according
to IP).
Rd/Wr 0 12
0 = SDTV Composite
1 = SDTV Y/C
2 = Video RGBS.
3 = Video RGB SOG
4 = Video YUV
5 = Computer SOG
6 = Computer HV/C
7 = Computer B&W
8 = DVI Video RGB
9 = DVI Video YUV
10 = DVI Computer 0-255
11 = DVI Computer 16-235
12 = SDI
IN IN Input signal type. Rd 0 33
0= No Signal 1= Wrong Signal
2= Unknown Signal 3= NTSC
4= PAL 5= SECAM
6= SDTV_BW 7= 480i
8= 576i 9= 480p
10= 576p 11= 720p
12= 1035i 13= 1080i
14= 1080p 15= 1080sf
16= VGA 640x480 17= SVGA 800x600
18= XGA 1024x768 19= 1280x 960
20= SXGA 1280x1024 21= DILA 1366x1024
22= SXGA+ 1400x1050 23= UXGA 1600x1200
24= WVGA 852x480 25= 1280 x 720
26= WXGA 1280 x 768 27= SWXGA 1366x768
28= 1280x800 29=WSXGA+1680x1050
30=1920x1080 31=WUXGA 1920x 1200
32=1440x900 33=2048x1536
IZ IZ H sync load selection (according to IP) Rd/Wr 0 1 0 = Hi-Z load 1 = 75
Ω load
Is Is
Input standard selection (according to
IC).
Rd/Wr 0 15
0 = Auto w/o Ped. 1 = Auto w/ Ped
2 = NTSC (J) 2 = NTSC (M)
4 = NTSC 4.43 5 = PAL BGHID
6 = PAL 60 7 = PAL N BGHID
8 = PAL M w/o Ped. 9 = PAL M
10 = PAL Comb. N 11 = PAL Comb. N Ped
12 = SECAM 13 = SECAM w Ped.
14 = B&W w/o Ped. 15 = B&W w/ Ped.
IA IA
Audio input assignment (according to
IC)
Rd/Wr 0 6
0 = No audio source assigned
1 = Input A
2 = Input B
3 = Input C 4 = Input D
5 = SPDIF 6 = Embedded SDI.
Ib Ib Audio delay mode selection Rd/Wr 0 1 0 = Auto 1 = Manual
IB IB Audio delay (in ms) Rd/Wr 0 500
NOTE: Rd = Read only command / Commande de lecture. Rd/Wr = Read and write command / Commande de lecture et d'écriture.
PAGE 36