Lincoln Electric IM635 RED-D-ARC GX 271Chopper LPG - Manual (Page 30)

GX 271 Chopper LPG
C-4 C-4 ACCESSORIES - CONNECTION DIAGRAMS
14 PIN
TO WORK
AMPHENOL
WARNING
Keep guards in place.
or service this equipment.
Keep away from moving parts.
Only qualified personnel should install,use
CONTROL MODULE CONNECTION DIAGRAM
Do not touch electrically live parts.
ELECTRODE TO WORK
CABLE PLUG
CAUTION :
DAMAGED. THE ENGINE GOVERNOR SETTING IS PRE-SET AT THE FACTORY - DO NOT ADJUST ABOVE RPM SPECIFICATIONS LISTED IN
N.A. PLACE THE MODE SWITCH IN THE "WIRE WELDING-CV" POSITION. PLACE WELDER TERMINALS SWITCH TO "REMOTELY
CONTROLLED" POSITION.
APPLICATIONS. SEE OPERATING MANUAL.
N.D. IF OPTIONAL REMOTE OUTPUT CONTROL IS USED, PLACE OUTPUT CONTROL SWITCH IN "OUTPUT CONTROL REMOTE" POSITIION.
S24095-3
AN INCREASE IN THE THE AC AUXILIARY VOLTAGE. IF THIS VOLTAGE GOES OVER 140 VOLTS, WIRE FEEDER CONTROL CIRCUITS MAY BE
THE ENGINE WELDER OPERATING MANUAL.
ANY INCREASE OF THE HIGH IDLE ENGINE RPM BY CHANGING THE GOVERNOR SETTING OR OVERRIDING THE THROTTLE LINKAGE WILL CAUSE
N.B. CONNECT WELDING CABLES TO OUTPUT STUDS FOR DESIRED POLARITY. POSITION THE WIRE FEEDER VOLTMETER SWITCH TO
MATCH THE POLARITY OF THE ELECTRODE CABLE.
ELECTRODE CABLE
TO WIRE FEED UNIT
GX-271 / LN-25 WITH K624-1 42 VOLT REMOTE OUTPUT
A
N.E. PLACE IDLER SWITCH IN "AUTO" OR "HIGH" IDLE POSITION AS DESIRED.
N.C. WELDING CABLES MUST BE OF PROPER CAPACITY FOR THE CURRENT AND DUTY CYCLE OF IMMEDIATE AND FUTURE
TO LN-25 INPUT
K626-XX INPUT CABLE ASSEMBLY
Do not operate with panels open.
Disconnect NEGATIVE (-) BATTERY LEAD
before servicing.
WARNING
Do not operate with panels open.
Disconnect NEGATIVE (-) BATTERY LEAD
before servicing.
Do not touch electrically live parts.
ELECTRODE TO WORK
A
GX-271 / LN-7 CONNECTION DIAGRAM
S24095-4
N.A. WELDING CABLES MUST BE OF PROPER CAPACITY FOR THE CURRENT AND DUTY CYCLE OF IMMEDIATE AND FUTURE
N.B. CONNECT WELDING CABLES TO OUTPUT STUDS FOR DESIRED POLARITY. POSITION THE WIRE FEEDER VOLTMETER SWITCH
TO MATCH POLARITY OF THE ELECTRODE CABLE.
N.D. IF OPTIONAL REMOTE OUTPUT CONTROL IS USED, PLACE LOCAL REMOTE SWITCH IN "REMOTE" POSITION.
APPLICATIONS. SEE OPERATING MANUAL.
N.C. PLACE THE MODE SWITCH IN THE " WIRE WELDING-CV" POSITION.
N.E. PLACE IDLER SWITCH IN "HIGH" POSITION.
CAUTION :
AN INCREASE IN THE THE AC AUXILIARY VOLTAGE. IF THIS VOLTAGE GOES OVER 140 VOLTS, WIRE FEEDER CONTROL CIRCUITS MAY BE
ANY INCREASE OF THE HIGH IDLE ENGINE RPM BY CHANGING THE GOVERNOR SETTING OR OVERRIDING THE THROTTLE LINKAGE WILL CAUSE
DAMAGED. THE ENGINE GOVERNOR SETTING IS PRE-SET AT THE FACTORY - DO NOT ADJUST ABOVE RPM SPECIFICATIONS LISTED IN
THE ENGINE WELDER OPERATING MANUAL.
TO LN-7 INPUT
CABLE PLUG
14 PIN
AMPHENOL
OPTIONAL K857
REMOTE CONTROL
6 PIN
AMPHENOL
ELECTRODE CABLE
TO WORK
TO WIRE FEED UNIT
Keep guards in place.
Keep away from moving parts.
Only qualified personnel should install,use
or service this equipment.
K584 CONTROL CABLE