Martel Electronics DMC1400 - Manual (Page 2)

8. Document Mode . . . . . . . . . . . .52
8.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . 52
8.2 New Tag As Found Test . . . . . . . . . . . . . . 64
8.3 Adjustment . . . . . . . . . . . . . . . . . . . . . . . 76
8.4 Downloaded Tag As Found Test . . . . . . . 79
8.5 As Left Test . . . . . . . . . . . . . . . . . . . . . . . 80
8.6 Viewing Test Results . . . . . . . . . . . . . . . . 82
8.7 Printing Test Results . . . . . . . . . . . . . . . . 84
8.8 Clearing Test Results. . . . . . . . . . . . . . . . 85
8.9 Setting Date & Time . . . . . . . . . . . . . . . . 85
9. USV Utility Program . . . . . . . . . .86
9.1 System Requirements . . . . . . . . . . . . . . . 86
9.2 Installation. . . . . . . . . . . . . . . . . . . . . . . . 87
9.3 Overview . . . . . . . . . . . . . . . . . . . . . . . . . 87
9.4 File Menu . . . . . . . . . . . . . . . . . . . . . . . . 88
9.5 Tags Menu . . . . . . . . . . . . . . . . . . . . . . . 88
9.6 Reports Menu . . . . . . . . . . . . . . . . . . . . . 91
9.7 Setup Menu . . . . . . . . . . . . . . . . . . . . . . 91
9.8 Configuration Menu. . . . . . . . . . . . . . . . . 92
9.9 Tag Configuration Details. . . . . . . . . . . . . 94
9.10 Group Configuration Details . . . . . . . . . 97
10. Specifications . . . . . . . . . . . . . .98
11. Maintenance / Warranty . . . . .102
1. Introduction . . . . . . . . . . . . . . . . .1
1.1 Customer Service . . . . . . . . . . . . . . . . . . . 1
1.2 Standard Equipment . . . . . . . . . . . . . . . . . 1
1.3 Safety Information . . . . . . . . . . . . . . . . . . 2
2. Calibrator Interface . . . . . . . . . . .5
2.1 Main Display . . . . . . . . . . . . . . . . . . . . . . 6
2.2 Menu Bar . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.3 Cursor Control / Setpoint Control . . . . . . 11
3. Using Measure Modes
(Lower Display) . . . . . . . . . . . . . .13
3.1 Measuring Volts and Frequency . . . . . . . 13
3.2 Measuring mA . . . . . . . . . . . . . . . . . . . . . 13
3.3 Measuring Temperature. . . . . . . . . . . . . . 13
3.4 Measuring Pressure . . . . . . . . . . . . . . . . 15
4. Using Source Modes
(Lower Display) . . . . . . . . . . . . . .17
4.1 Setting 0 % and 100 % Output
Parameters . . . . . . . . . . . . . . . . . . . . . . . 17
4.2 Using the Automatic Output Functions. . . 18
4.3 Sourcing mA . . . . . . . . . . . . . . . . . . . . . 18
4.3-1 HART™ Resistor Selection . . . . . . . . . . 19
4.4 Simulating a Transmitter . . . . . . . . . . . . . 19
4.5 Sourcing Volts . . . . . . . . . . . . . . . . . . . . . 20
4.6 Sourcing Frequency . . . . . . . . . . . . . . . . 21
4.7 Sourcing a Pulse Train . . . . . . . . . . . . . . 21
4.8 Sourcing Thermocouples . . . . . . . . . . . . 22
4.9 Sourcing Ohms/RTDs . . . . . . . . . . . . . . . 23
5. Using Isolated Measure Modes
(Upper Display) . . . . . . . . . . . . .24
5.1 Measuring Volts and mA . . . . . . . . . . . . . 24
5.2 Measuring Current with Loop Power . . . . 25
5.2-1 HART™ Resistor Selection. . . . . . . . . . 25
5.3 Measuring Pressure . . . . . . . . . . . . . . . . 26
6. Using the Upper and the
Lower Display for Calibration
and Testing . . . . . . . . . . . . . . . . .27
6.1 Testing an Input or Indicating Device. . . . 27
6.2 Calibrating an I/P Device . . . . . . . . . . . . . 28
6.3 Calibrating a Transmitter . . . . . . . . . . . . . 28
6.4 Calibrating a Pressure Transmitter . . . . . . 29
7. Remote Operation . . . . . . . . . . .30
7.1 Setting up the RS-232 Port for
Control . . . . . . . . . . . . . . . . . . . . . . . . . . 31
7.2 Changing Between Remote and
Local Operation . . . . . . . . . . . . . . . . . . . 31
7.3 Using Commands . . . . . . . . . . . . . . . . . . 32
7.4 Remote Commands and Error Codes . . . 36
7.5 Entering Commands . . . . . . . . . . . . . . . . 39