Document Outline

• HP ProLiant DL120 G7 Server User Guide
• Abstract
• Notice
• Contents
• Component identification
  • Front panel components
  • Front panel LEDs
  • Rear panel components
  • Rear panel LEDs
  • PCIe expansion slot definitions
  • System board components
    • System board LEDs
    • System maintenance switch
    • NMI functionality
    • DIMM slot locations
  • SAS and SATA device numbering
  • SAS and SATA drive LEDs
  • BBWC module LEDs
  • Fan locations
  • T-10/T15 Torx screwdriver
• Operations
  • Power up the server
  • Power down the server
  • Remove the server from the rack
  • Remove the access panel
  • Install the access panel
  • Remove the PCIe riser cage
  • Install the PCIe riser cage
  • Remove the air baffle
  • Install the air baffle
• Setup
  • Optional installation services
  • Rack planning resources
  • Optimum environment
    • Space and airflow requirements
    • Temperature requirements
    • Power requirements
    • Electrical grounding requirements
  • Rack warnings
  • Identifying the contents of the server shipping carton
  • Installing hardware options
  • Installing the server into the rack
  • Powering up and configuring the server
  • Installing the operating system
  • Registering the server
• Hardware options installation
  • Introduction
  • Memory options
    • Memory subsystem architecture
    • Single-rank and dual-rank DIMMs
    • DIMM identification
    • UDIMM maximum memory configurations
    • Memory configuration
      • ECC memory configuration
    • General DIMM slot population guidelines
    • Installing a DIMM
  • Drive options
    • Drive guidelines
    • Removing a drive blank
    • Removing a drive
    • Installing a hot-plug drive
  • Optical drive option
  • Dedicated iLO management port module option
  • Expansion board option
  • Storage controller option
  • BBWC module and battery pack option
  • Redundant hot-plug power supply option (with cage)
  • HP Trusted Platform Module option
    • Installing the Trusted Platform Module board
    • Retaining the recovery key/password
    • Enabling the Trusted Platform Module
• Cabling
  • Cabling overview
  • Server cabling
  • Nonredundant power supply cabling
  • Redundant power supply cabling
  • Internal USB cabling
  • BBWC battery cabling
  • Optical drive cabling
  • SATA cabling
  • SAS cabling
• Configuration and utilities
  • Configuration tools
    • SmartStart software
      • SmartStart Scripting Toolkit
    • HP ROM-Based Setup Utility
      • Using RBSU
      • Auto-configuration process
      • Boot options
      • BIOS Serial Console
    • Array Configuration Utility
    • Option ROM Configuration for Arrays
    • Re-entering the server serial number and product ID
  • Management tools
    • Automatic Server Recovery
    • ROMPaq utility
    • Integrated Lights-Out 3 technology
    • Erase Utility
    • USB support
  • Diagnostic tools
    • HP Insight Diagnostics
    • HP Insight Diagnostics survey functionality
    • Integrated Management Log
  • Remote support and analysis tools
    • HP Insight Remote Support software
  • Keeping the system current
    • Drivers
    • Version control
    • ProLiant Support Packs
    • Operating System Version Support
    • Firmware
    • HP Smart Update Manager
    • Change control and proactive notification
    • Care Pack
• Troubleshooting
  • Pre-diagnostic steps
    • Important safety information
      • Symbols on equipment
      • Warnings and cautions
    • Symptom information
    • Prepare the server for diagnosis
      • Performing processor procedures in the troubleshooting process
      • Breaking the server down to the minimum hardware configuration
  • Loose connections
  • Service notifications
  • Server health LEDs
  • Troubleshooting flowcharts
    • Start diagnosis flowchart
    • General diagnosis flowchart
    • Server power-on problems flowchart
    • POST problems flowchart
    • OS boot problems flowchart
    • Server fault indications flowchart
  • POST error messages and beep codes
• Battery
• Regulatory compliance notices
  • Regulatory compliance identification numbers
  • Federal Communications Commission notice
    • FCC rating label
    • FCC Notice, Class A Equipment
  • Declaration of conformity for products marked with the FCC logo, United States only
  • Modifications
  • Cables
  • Canadian notice (Avis Canadien)
  • European Union regulatory notice
  • Disposal of waste equipment by users in private households in the European Union
  • Japanese class A notice
  • BSMI notice
  • Korean class A notice
  • Chinese notice
  • Laser compliance
  • Battery replacement notice
  • Taiwan battery recycling notice
  • Power cord statement for Japan
• Electrostatic discharge
  • Preventing electrostatic discharge
  • Grounding methods to prevent electrostatic discharge
• Specifications
  • Environmental specifications
  • Mechanical specifications
  • Power supply specifications
• Support and other resources
  • Before you contact HP
  • HP contact information
  • Customer Self Repair
• Acronyms and abbreviations
• Documentation feedback
• Index