Kenwood KDC-X898 - Manual (Page 18)

18 |
KDC-X998/ KDC-BT958HD/ KDC-X898/ KDC-BT858U
5. DSP settings (KDC-X998, KDC-BT958HD)
5-1. Audio control
You can adjust the audio control items.
1
Press [SRC] and select a source other than
Standby (“STANDBY”) using [Control] knob.
Refer to
<Source selection> (page 14) .
2
Press [Control] knob.
Enters the Function setting mode.
3
Select “Audio Control” using [Control] knob.
For how to use [Control] knob, refer to
<3-3. How
to select the item> (page 13) .
4
Select a audio control item using [Control]
knob.
Display Overview
“SubWoofer Level” You can set subwoofer level.
“–15” — “0” — “+15”
“Drive Equalizer” [5] Sets the sound quality to reduce the road
noise.
“ ON ”/ “OFF”
“Preset Equalizer” [1][5] Select from among preset equalizer curves
to set the sound quality.
“ User ” [2] / “iPod”(During iPod source
only)/ “Top 40”/ “Powerful”/ “Rock”/
“Pops”/ “Easy”/ “Jazz”/ “Natural”
“Manual Equalizer” [1][5] Set the equalizer curve manually.
Refer to <5-2. Manual equalizer control>
(page 19) .
“Pro Setup”
“DSP Set” Turn on/off the DSP function.
“Bypass”: Disables the DSP function.
“ Through ”: Enables the DSP function.
“Car Type” [5] To get clear sound, set the sound
environment according to the location and
size of physically installed speakers with
reference to the followings:
<5-3. Car type selection> (page 19)
<5-4. Speaker setting> (page 20)
<5-5. X’Over setting> (page 20)
<5-6. Listening position setting> (page
21)
<5-7. Delay time control> (page 22)
<5-8. Channel level fine adjustments>
(page 23)
“Speaker Setting” [5]
“X’Over” [5]
“DTA Settings” [5]
“Sound Enhancements” [5]
“Supreme” [6] Turns ON/OFF the Supreme function.
Can be set while Audio file source of USB/
CD and iPod source.
“ ON ”/ “OFF”
“Space Enhancer” [3]
[4]
Virtually enhances the sound space using
the DSP.
“ OFF ”/ “Small”/ “Medium”/ “Large”
“Sound Realizer” [4] Virtually makes the sound more realistic
using the DSP.
“ OFF ”/ “Level1”/ “Level2”/ “Level3”
“Sound Elevation” [4] Virtually raises the sound field using
the DSP.
“ OFF ”/ “Low”/ “Middle”/ “High”
“Volume offset” Sets each source’s volume as a difference
from the basic volume.
“–8” — “ 0 ” (AUX: “–8”— “+8”)
“SubWoofer Mute” Sets the Subwoofer Mute.
“ON”/ “ OFF ”
“Audio Preset” You can register the values set the Audio
control items.
Refer to <5-10. DSP preset> (page
24) , <5-11. DSP preset recall> (page
24) .
“Bass Boost” [5] Sets the Bass Boost level in 3 steps.
“ OFF ”/ “Level1”/ “Level2”/ “Level3”
“Loudness” [5] Makes the sounds at high and low
frequencies louder.
“ OFF ”/ “Low”/ “High”
“Balance” Adjusts left/right speaker balance.
“Left15” — “ 0 ” — “Right15”
“Fader” Adjusts front/rear speaker balance.
“Rear15” — “ 0 ” — “Front15”
( Colored text : Factory setting)
[1] You can select for each source.
[2] “User”: The Equalizer curve set in the section <5-2.
Manual equalizer control> (page 19) is recalled.
[3] This function is not effective for the HD Radio source.
[4] Function of KDC-X998.
[5] Displayed only when “DSP Set” is set to ”Through”.
[6] Audio file source only
5
Select a value using [Control] knob.
Exiting from the Function setting mode
Press and hold [ 1/6].
When you selected “iPod” for “Preset Equalizer”
• When you selected “iPod” for “Preset Equalizer”, next select
an equalizer curve. Select a desired equalizer curve using
[Control] knob from among 22 equalizer curves displayed
after you selected “iPod”.