MagTek IntelliStripe 320 99875167 - Manual (Page 2)

ii
Copyright
©
2000-2013
MagTek
®
, Inc.
Printed in the United States of America
Information in this document is subject to change without notice. No part of this document may be
reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose,
without the express written permission of MagTek, Inc.
MagTek is a registered trademark of MagTek, Inc.
IntelliStripe is a registered trademark of MagTek, Inc.
REVISIONS
Rev
Number
Date Notes
1 12 May 00 Initial Release
2 23 Aug 00 Section 1, Added Front Gate caution; all U.S. dimensions, weights, and temp listed
first and metric last and in ( ), editorial. Sec 3, Fig 3-1, Changed capacitor wire from
5.1672 in to 79 in.
3 18 Oct 00 Sec 1: Electrical Spec Change: from 1 Amp max to 1.5 A, and from 100 Ma to 170 Ma
typical. Changed specs to SI Metric System.
4 6 Dec 00 Editorial throughout. Section 1, Specifications: Changed length from 5.60” to 5.85” to
add dimension of flex cable extension. Section 2: Changed Figure 2-3 to reflect flex
cable extension. Changed Figure 2-7 to add Red and Green callouts to LED.
Changed Figure 2-8, 7-pin connector to reflect pin numbers and locking tabs.
5 22 Feb 01 Sec 1: Deleted P/N 16050327,added P/Ns 16050330, 16050337. Accessories:
Changed 2-disk set to 4-disk set. Specifications, Dimensions: Changed width from
3.26” to 3.27”; Height from 2.17” to 2.18”; Weight from 15.33 oz to 15.4 oz and Bezels
Wts. From 1.37 to 1.40 oz. Sec 2: Changed Figure 2-1 to Bezel Options. Changed
Fig 2-2 Bezel Width from 3.264” to 3.27” and height from 2.17” to 2.18”. Fig 2-3 Bezel
width from .98” to 1.00”. Sec 3: Changed “Section 3” to “Appendix A”. Changed dwg
(Fig A-1) to include polarity pin (+).
6 26 Apr 01 Changed illustrations throughout for clarity and added “D” Bezel. Front Matter:
Changed warranty Address to 20801 S. Annalee. Added EMVCo statement. Editorial
corrections Sec 1: To configurations added P/N 16050329 “D” Bezel. Specifications:
Added “B”, “C”, and “D” bezel dimensions and weights.
7 16 Aug 01 Section 2, Fig 2-8, Corrected dimensions on D inner panel opening: Changed 4.00” to
3.745” and Changed 2.00” to 1.873”.
8 2 May 02 Section 1: Added JIS to Specifications
9 09 May 03 Front Matter: Added ISO line to logo, changed Tech Support phone number, added
new warranty statement; Sec 2: Changed converted values in Figures 2-3, 2-4, 2-5,
2-6 and 2-8; Appendix A, Changed converted value in Figure A-3.
10 17 Feb 04 Options: Added paragraph: “In the special case where the card eject capacitor is
being used…”
11 23 Jun 04 Editorial throughout. Sec 1, Added USB Power Cable, CDs for drivers, and Internet
P/Ns for downloads. Added USB description and use.
12 1 Sep 06 Removed old models and added new models with USB interface (16050307, -08, -09,
-10); removed references to “B” bezel
13 3 Mar 07 Added RoHS information. Included information about the OTI Contactless reader
module; added 16050314 & -15.
14 26 Mar 07 Clarified FCC statement; changed the EMV version from 3.1.1 to 4.1
15 20 Aug 09 Updated Warranty and Agency information; added 16050316, -17 & -19; added
accessories for contactless support
16 19 Aug 10 Changed minimum temperature from -40°C to -20°C
17 18 Oct 12 Update figures to be more readable