Document Outline

• Contents
• Figures
• Tables
• Preface
  • Safety Symbols Used in this Document
  • Contacting Allied Telesis
• Chapter 1
  • Overview of the Chassis and Power Supplies
    • Introduction
    • AT-SBx3106 Chassis
    • Slots for the Ethernet Line and Controller Cards
    • Slots for the Power Supplies
    • Power Supplies
      • LEDs
    • AT-SBxFAN06 Module
      • LED
    • Power Supply Interfaces (Opto-couplers)
      • LED
• Chapter 2
  • Overview of the Ethernet Line Cards
    • Ethernet Line Cards
    • AT-SBx31GT24 Line Card
      • LEDs
    • AT-SBx31GT40 Line Card
      • LEDs
    • AT-SBx31GP24 PoE Line Card
      • LEDs
    • AT-SBx31GS24 SFP Line Card
      • LEDs
    • AT-SBx31GC40 Line Card
      • Port Numbers
      • LEDs
    • AT-SBx31XZ4 XFP Line Card
      • LEDs
    • AT-SBx31XS6 SFP+ Line Card
      • LEDs
    • 10/100/1000Base-T Twisted Pair Ports
      • Connector Type
      • Speed
      • Duplex Mode
      • Maximum Distance
      • Cable Requirements
      • Automatic MDIX Detection
      • Straight-through or Crossover Cabling
      • Port Pinouts
    • Power over Ethernet on the AT-SBx31GP24 Line Card
      • Powered Device Classes
      • Power Budgeting
      • PoE Wiring
• Chapter 3
  • Overview of the AT-SBx31CFC960 Controller Fabric Card
    • Hardware Components
    • Guidelines
    • Dual Controller Cards
    • SYS Status LEDs
    • eco-friendly Button
    • SBx Linecard Status LEDs
    • SFP+ Slots
    • Console (RS-232) Port
    • NET MGMT Port
      • NET MGMT Port LED
    • USB Port
    • Reset Button
    • Release Activation and Feature Licenses
• Chapter 4
  • Safety Precautions and Site Preparation
    • Reviewing Safety Precautions
    • Selecting a Site for the SwitchBlade x3106
    • Installation Tools and Material
• Chapter 5
  • Installing the Chassis on a Table or in an Equipment Rack
    • Unpacking the AT-SBx3106 Chassis
    • Installing the Chassis on a Table
    • Installing the Chassis in an Equipment Rack
      • Required Tools and Material
      • Preparing the Equipment Rack
      • Removing the Rubber Feet
      • Adjusting the Equipment Rack Brackets
      • Installing the Chassis in the Equipment Rack
    • Removing the Shipping Brace
    • Installing the Chassis Grounding Lug
• Chapter 6
  • Installing the Power Supplies
    • Protecting Against Electrostatic Discharge (ESD)
    • Installing the AT-SBxPWRSYS1 AC System Power Supply
    • Installing the AT-SBxPWRPOE1 AC Power Supply
    • Installing the AT-SBxPWRSYS1 DC Power Supply
• Chapter 7
  • Installing the AT-SBx31CFC960 Card and Ethernet Line Cards
    • Guidelines to Handling the Controller and Line Cards
    • Installing the AT-SBx31CFC960 Controller Fabric Card
    • Installing the Ethernet Line Cards
    • Installing the Blank Slot Covers
• Chapter 8
  • Installing the Transceivers and Cabling the Ports
    • Guidelines to Cabling the Twisted Pair Ports on the AT-SBx31GP24, AT-SBx31GT24, and AT-SBx31GT40 Line Cards
      • Connecting Cables to the AT- SBx31GT40 Line Card
    • Guidelines to Installing SFP, SFP+, CSFP, and XFP Transceivers
    • Installing SFP Transceivers in the AT-SBx31GS24 Line Card
    • Installing SFP and CSFP Transceivers in the AT-SBx31GC40 Line Card
    • Installing SFP+ Transceivers in the AT-SBx31XS6 Line Card
    • Installing AT-SP10TW Cables in the AT-SBx31XS6 Line Card
    • Installing XFP Transceivers in the AT-SBx31XZ4 Line Card
    • Cabling the NET MGMT Port on the AT-SBx31CFC960 Card
    • Installing SFP or SFP+ Transceivers in the AT-SBx31CFC960 Card
• Chapter 9
  • Powering On the Chassis
    • Verifying the Installation
    • Powering On the AT-SBxPWRSYS1 AC Power Supply
    • Powering on the AT-SBxPWRPOE1 AC Power Supply
    • Powering On the AT-SBxPWRSYS1 DC System Power Supply
      • Choosing a Method for Attaching the Grounding Wire
      • Connecting the Grounding Wire with the Grounding Terminal
      • Connecting the Grounding Wire with Bare Wire
      • Choosing a Method for Attaching the Power Wires
      • Connecting the DC Power Wires with the Straight Terminals
      • Connecting the DC Power Wires with the Right Angle Terminals
      • Connecting Bare DC Power Wires
    • Monitoring the Initialization Process
      • Using the LEDs to Monitor the Initialization Process
      • Using the Console Port to Monitor the Initialization Process
• Chapter 10
  • Verifying the Hardware Operations of the Chassis
    • Using the LEDs to Verify the Chassis
    • Using Local Management to Verify the Chassis
      • Starting a Local Management Session
      • Entering the Management Software Commands
    • Running the Easy Startup Application
• Chapter 11
  • Upgrading AT-SBx31CFC to AT- SBx31CFC960 Controller Fabric Cards
    • Guidelines
    • Upgrading the Controller Fabric Cards
• Chapter 12
  • Troubleshooting
    • AT-SBxPWRSYS1 and AT-SBxPWRPOE1 AC Power Supplies
    • AT-SBxPWRSYS1 DC Power Supply
    • Ethernet Line Cards
    • Twisted Pair Ports
    • Power Over Ethernet
    • Fiber Optic Transceivers
    • AT-SBx31CFC960 Controller Fabric Card
    • AT-SBxFAN06 Fan Module
    • Local (Out-of-Band) Management Session
    • Power Supply Interfaces (Opto-couplers)
• Chapter 13
  • Replacing Modules
    • Replacing AT-SBxPWRSYS1 AC and AT-SBxPWRPOE1 Power Supplies
    • Replacing the AT-SBxPWRSYS1 DC Power Supply
    • Replacing Ethernet Line Cards
    • Replacing the AT-SBx31CFC960 Controller Fabric Card
    • Replacing the AT-SBxFAN06 Fan Module
      • Removing the AT-SBxFAN06 Fan Module
      • Installing a New AT-SBxFAN06 Fan Module
• Appendix A
  • Technical Specifications
    • Physical Specifications
    • Environmental Specifications
    • Power Specifications
    • Safety and Electromagnetic Emissions Certifications
    • Port Pinouts