Beijer Electronics BFI-P2 V1.21 User Manual
Page 36
User Guide Revision 1.12
www.beijerelectronics.com
36
P1‐13
Digital Input 1
(Terminal 2)
Digital Input 2
(Terminal 3)
Digital Input 3
(Terminal 4)
Analog Input 1
(Terminal 6)
Analog Input 2
(Terminal 10)
11
O: Stop
C: Run Fwd
O: Stop
C: Run Rev
O: Selected Speed Ref
C: Preset speed 1, 2
Analog 1 Speed reference
O: Preset speed 1
C: Preset speed 2
12
O: Stop
C: Run Fwd
O: Stop
C: Run Rev
Digital input 3
Analog input 1
Analog input 2
Preset Speed
Off
Off
Off
Preset Speed 1
On
Off
Off
Preset Speed 2
Off
On
Off
Preset Speed 3
On
On
Off
Preset Speed 4
Off
Off
On
Preset Speed 5
On
Off
On
Preset Speed 6
Off
On
On
Preset Speed 7
On
On
On
Preset Speed 8
13
O: Stop
C: Run Fwd
O: Stop
C: Run Rev
O: Selected Speed Ref
C: Preset speed 1
Analog 1 Speed reference
Analog torque reference
14
O: Stop
C: Run Fwd
O: Stop
C: Run Rev
O: Selected Speed Ref
C: Preset speed 1
Analog 1 Speed reference
O: Decel ramp 1 (P1‐04)
C: Decel ramp 2 (P8‐11)
15
O: Stop
C: Run Fwd
O: Stop
C: Run Rev
O: Selected Speed Ref
C: Analog input 2
Analog 1 Speed reference
Analog 2 Speed reference
16
O: Stop
C: Run Fwd
O: Stop
C: Run Rev
O: Selected Speed Ref
C: Preset speed 1
Analog 1 Speed reference
External trip *
O: trip C: Run
17
O: Stop
C: Run Fwd
O: Stop
C: Run Rev
Digital input 3
Analog input 1
Preset Speed
External trip *
O: trip C: Run
Off
Off
Preset Speed 1
On
Off
Preset Speed 2
Off
On
Preset Speed 3
On
On
Preset Speed 4
18
O: Stop
C: Run Fwd
O: Stop
C: Run Rev
Digital input 3
Analog input 1
Preset Speed
O: Decel ramp 1 (P1‐04)
C: Decel ramp 2 (P2‐25)
Off
Off
Preset Speed 1
On
Off
Preset Speed 2
Off
On
Preset Speed 3
On
On
Preset Speed 4
19
O: Stop
C: Run Fwd
O: Stop
C: Run Rev
Digital input 3
Analog input 1
Preset Speed
O: Selected Speed Ref
C: Preset speed 1 .. 4
Off
Off
Preset Speed 1
On
Off
Preset Speed 2
Off
On
Preset Speed 3
On
On
Preset Speed 4
20
O: Stop
C: Run Fwd
O: Stop
C: Run Rev
Normally Open (N.O.)
Close to increase speed
Normally Open (N.O.)
Close to reduce speed
O: Selected Speed Ref
C: Preset speed 1
21
Normally Open (N.O.)
Close to run Fwd
Normally Closed (N.C.)
Open to Stop
Normally Open (N.O.)
Close to run Rev
Analog 1 Speed reference
O: Selected Speed Ref
C: Preset speed 1
The “Selected Speed Reference” referred to in the above table is determined by the value set in P1‐12 (Control Mode) :
P1‐12 (control Mode)
Selected Speed Reference
0 : Terminal Mode
Analog input 1
1 : Keypad Mode (uni‐directional)
Digital Potentiometer
2 : Keypad Mode (bi‐directional)
Digital Potentiometer
3 : User PID mode
PID controller output
4 : Fieldbus Control
Speed reference via Fieldbus
5 : Slave Mode
Speed reference via Master / Slave function
Note
1) To access P8‐11, set P1‐14 = 201
2) If a motor thermistor (PTC type only, or normally closed thermal switch contact) is to be connected, this must be selected in P2‐33.
Connect the thermistor between terminal 1 and terminal 10.