NOVUS Controller N2000 - Manual (Page 6)

Controller N2000
NOVUS AUTOMATION 6/9
CONFIGURATION CYCLE
type type type type INPUT TYPE: Selects the input signal type to be connected
to the process variable input. Refer to Table 1.
This is the first parameter to be set.
dppo dppo dppo dppo DECIMAL POINT POSITION: For input types 16, 17, 18 or
19 only. Selects the decimal point position to be viewed in
both PV and SV.
vn vn vn vnI I I It t t t TEMPERATURE INDICATION IN ºC OR ºF: Selects the
display indication to be in ºC or ºF. Only available if input type
is other than 16, 17, 18 or 19.
offs offs offs offs SENSOR OFFSET: Offset value to be added to the PV to
compensate sensor error. Default value: zero.
spll spll spll spll SET POINT LOW LIMIT:
- Linear inputs: Sets the lower range for SV and PV indication.
- T/C and Pt100 inputs: sets the lower range for SV.
spxl spxl spxl spxl SET POINT HIGH LIMIT:
- Linear inputs: Sets the upper range for SV and PV indication.
- T/C and Pt100 inputs: sets the upper range for SV.
rsll rsll rsll rsll REMOTE SET POINT LOW LIMIT: Selects the lower range
for indication of the Remote Setpoint.
rsxl rsxl rsxl rsxl REMOTE SET POINT HIGH LIMIT: Selects the upper range
for indication of the Remote Setpoint.
bavd bavd bavd bavd DIGITAL COMMUNICATON BAUD RATE SELECTION:
0: 1200bps; 1: 2400bps; 2: 4800bps; 3: 9600bps; 4: 19200bps.
addr addr addr addr SLAVE ADDRESS SELECTION: Identifies a slave in the
network. The possible address numbers are from 1 to 247.
I/O CYCLE (INPUTS AND OUTPUTS)
I I I Io 1 o 1 o 1 o 1 I/O 1 FUNCTION: Selects the I/O function to be used at I/O 1
(relay 1). Options 0 to 5 are possible for this output. It is
normally used as option 5, PWM main control output. Refer to
Table 2 for functions.
I I I Io 2 o 2 o 2 o 2 I/O 2 FUNCTION: Selects the I/O function to be used at I/O 2
(relay 2). Options 0 to 5 are available. This output is normally
used as alarm output. See Table 2 for functions.
I I I Io 3 o 3 o 3 o 3 I/O 3 FUNCTION: Selects the I/O function to be used at I/O 3
(option 1). I/O 3 can be a relay output or a digital input/output.
Functions 0 to 10 are available. Refer to Table 2 for
functions. The presence of this I/O option is detected by the
controller and the prompt menu will only be shown if the
expansion option is available.
I I I Io 4 o 4 o 4 o 4 I/O 4 FUNCTION: Selects the I/O function to be used at I/O 4
(option 2). I/O 4 can be a digital input/output. Functions 0 to
10 are available. Refer to Table 2 for functions. The prompt
menu will only be shown if the expansion option is present.
I I I Io 5 o 5 o 5 o 5 I/O 5 FUNCTION: Selects the I/O function to be used at I/O 5
(Analog Output). Functions 0 to 15 are available (See Table
2). This option is normally used for main control output or PV
analog retransmission.
I o 6 I o 6 I o 6 I o 6
I/O 6 FUNCTION: Selects the I/O function to be used at I/O 6
(Digital Input). Options 0, 6, 7, 8, 9 and 10 are possible for
this input. Refer to Table 2 for functions.
f.fvnc f.fvnc f.fvnc f.fvnc F KEY FUNCTION: Selects the I/O function assigned to the
front panel
F key. Available functions are:
0 0 0 0 - Key not used;
7
7 7 7 - Start/Stop the controller (RUN function);
8
8 8 8 - Select remote setpoint;
9
9 9 9 - Execute/Hold ramp and soak profile;
10
10 10 10- Enable/Disable ramp and soak profile 1;
Details on these functions are described in section 5.2.
aven aven aven aven ENABLE THE key – Enable or disable operation of the
key.
Yes Yes Yes Yes key enabled.
NO NO NO NO key disabled.
CALIBRATION CYCLE
All input and output types are factory calibrated. This cycle should
only be accessed by experienced personnel. If in doubt do not press
the
or keys in this cycle.
Inl( Inl( Inl( Inl( INPUT LOW CALIBRATION: Sets the Process Variable low
calibration (offset). Several keystrokes at
or might be
necessary to increment one digit.
Inx( Inx( Inx( Inx( INPUT HIGH CALIBRATION: Sets the Process Variable span
calibration (gain).
ovll ovll ovll ovll OUTPUT LOW CALIBRATION: Sets the analog current
output low calibration (offset).
Ovx( Ovx( Ovx( Ovx( OUTPUT HIGH CALIBRATION: Sets the analog current
output span calibration (gain).
(j l (j l (j l (j l COLD JUNCTION OFFSET CALIBRATION: Sets the cold
junction offset calibration.
Rsl( Rsl( Rsl( Rsl( REMOTE SET POINT LOW CALIBRATION: Sets the
Remote Set Point low calibration (offset). Several keystrokes
at
or might be necessary to increment one digit.
Rsx( Rsx( Rsx( Rsx( REMOTE SET POINT HIGH CALIBRATION: Sets the
Remote Set Point span calibration (gain).
Table 10 shows the sequence of cycles and parameters presented in the indicator display. There are parameters that must be defined for each
alarm available.
OPERATION CYCLE AUTO TUNING CYCLE PROGRAMMING CYCLE ALARM CYCLE CONFIGURATION CYCLE I/O CYCLE
PV and SP Atvn Atvn Atvn Atvn Tbas Tbas Tbas Tbas Fva1 Fva1 Fva1 Fva1 - fva4 fva4 fva4 fva4 type type type type Io 1 Io 1 Io 1 Io 1
Avto Avto Avto Avto Pb Pb Pb Pb Prn Prn Prn Prn Bla1 Bla1 Bla1 Bla1 - bla4 bla4 bla4 bla4 Dp.po Dp.po Dp.po Dp.po Io 2 Io 2 Io 2 Io 2
PV and MV Ky.st Ky.st Ky.st Ky.st ptol ptol ptol ptol Kya1 Kya1 Kya1 Kya1 - kya4 kya4 kya4 kya4 Vnit Vnit Vnit Vnit Io 3 Io 3 Io 3 Io 3
prn prn prn prn ir ir ir ir Psp0 Psp0 Psp0 Psp0 - PsP7 PsP7 PsP7 PsP7 A1t1 A1t1 A1t1 A1t1 offs offs offs offs Io 4 Io 4 Io 4 Io 4
rvn rvn rvn rvn dt dt dt dt Pt1 Pt1 Pt1 Pt1 – Pt7 Pt7 Pt7 Pt7 A1t2 A1t2 A1t2 A1t2 Spll Spll Spll Spll Io 5 Io 5 Io 5 Io 5
(t (t (t (t Pe1 Pe1 Pe1 Pe1 – Pe7 Pe7 Pe7 Pe7 A2t1 A2t1 A2t1 A2t1 spkl spkl spkl spkl Io 6 Io 6 Io 6 Io 6
Act Act Act Act lp lp lp lp A2t2 A2t2 A2t2 A2t2 rsll rsll rsll rsll f.fvnc f.fvnc f.fvnc f.fvnc
bias bias bias bias rskl rskl rskl rskl aven aven aven aven
Table 10