NOVUS Controller N1100 - Manual (Page 5)

Controller N1100
NOVUS AUTOMATION 5/8
CONFIGURATION PARAMETERS
OPERATION CYCLE
PV Indication
(Red)
SV Indication
(Green)
PV AND SV INDICATION: The status display shows the
present value of PV (Process Variable). The parameter
display shows SV (Set Variable).
The status display shows “--- --- --- ---- - - -“ whenever PV exceeds the
maximum range or there is no signal at the input. In case of
hardware error the status display will show Ern
Ern Ern Ern, where n is
the error code.
avto avto avto avto CONTROL MODE: YES indicates automatic control mode
(closed loop, PID or ON/OFF). NO indicates manual control
mode (open loop). Bumpless transfer from auto
↔ to
manual mode is available. If in doubt program YES.
PV Indication
(Red)
MV Indication
(Green)
MANIPULATED VARIABLE VALUE (MV): The upper display
shows PV value and the lower display shows the percentage
of MV applied to the control output. When in manual control
the MV value can be manually changed. When in auto mode
the MV value can only be viewed.
To distinguish the MV display from the SV display, the MV
is shown flashing intermittently.
Pr n Pr n Pr n Pr n RAMP AND SOAK PROGRAM SELECTION: Selects the
ramp and soak program to be executed (7 programs
possible). Refer to chapter 7 for R&S description.
rvn rvn rvn rvn CONTROL ENABLE: YES means that the control output
and alarms are enabled and NO means they are disabled.
AUTO TUNING CYCLE
atvn atvn atvn atvn AUTO-TUNE: YES enables the auto tuning of the PID
parameters and NO disables it.
Pb Pb Pb Pb PROPORTIONAL BAND: Percentage of maximum input
span. Select zero for ON/OFF control.
xyst xyst xyst xyst CONTROL HYSTERESIS (in engIneering. units): This
parameter is only shown for ON / OFF control (Pb=0).
‘ ir‘ ‘ ir‘ ‘ ir‘ ‘ ir‘ INTEGRAL RATE: Integral time constant in repetitions per
minute (Reset).
dt dt dt dt DERIVATIVE TIME: Derivative time constant, in seconds.
(t (t (t (t CYCLE TIME: PWM period in seconds. Can only be viewed
if proportional band is other than zero.
act act act act CONTROL ACTION: For Auto Mode only.
• rE rE rE rE Reverse Action usually used for heating.
• dir dir dir dir Direct Action usually used for cooling.
bias bias bias bias Offset for MV (manual reset). Range: -100 % to +100 %.
Default value: 0.
ovll ovll ovll ovll OUTPUT LOW LIMIT: minimum percentage value for MV
(Manipulated Variable) when in automatic control and PID.
Default value: 0.0 %
ovxl ovxl ovxl ovxl OUTPUT HIGH LIMIT: Maximum percentage value for MV
when in automatic control and PID. Default value: 100.0%
sfst sfst sfst sfst SOFT START: Time in seconds during which the controller
limits the MV value progressively from 0 to 100 %. It is
enabled at power up or when the control output is
activated. If in doubt set zero.
Sp.a1 Sp.a1 Sp.a1 Sp.a1
Sp.a2
Sp.a2 Sp.a2 Sp.a2
Sp.a3
Sp.a3 Sp.a3 Sp.a3
Sp.a4
Sp.a4 Sp.a4 Sp.a4
ALARM PRESET: Tripping point for alarm 1, 2, 3 and 4.
RAMP AND SOAK PROFILE PROGRAMMING CYCLE
tbas tbas tbas tbas TIME BASE: Selects the time base for the ramp and soak.
Valid for all profile programs.
0 0 0 0 - PT1 to PT7 values are in seconds;
1 1 1 1 - PT1 to PT7 values are in minutes;
Pr n Pr n Pr n Pr n PROGRAM TO BE VIEWED: Selects the ramp and soak
profile program to be edited/viewed in the following cycle
prompts (7 programs available).
ptol ptol ptol ptol RAMP AND SOAK TOLERANCE: maximum deviation
between PV and SV. Whenever this deviation is exceeded
the time counter is halted until deviation lowers to within the
tolerance. Set zero to disable this function.
Psp0 Psp0 Psp0 Psp0
Psp7 Psp7 Psp7 Psp7
RAMP AND SOAK SET POINTS (0 to 7): Set of 8 SV
values which define the ramp and soak profile segments.
See also PT1 to 7 and PE1 to 7 below.
Pt1 Pt1 Pt1 Pt1
Pt7 Pt7 Pt7 Pt7
RAMP AND SOAK SEGMENTS TIME (1 to 7): Set of 7
time intervals in minutes or seconds (9999 max.) for the 7
segments of the ramp and soak program.
Pe1 Pe1 Pe1 Pe1
Pe7 Pe7 Pe7 Pe7
RAMP AND SOAK EVENT (1 to 7): Set of 7 values that
define which alarms must be activated during a ramp and
soak program segment. Alarm function depends on “rS
rS rS rS”
setting (Table 3).
lp lp lp lp LINK TO PROGRAM: Number of the next profile program
to be linked to follow the current profile. Profiles can be
linked to make larger programs of up to 49 segments.
ALARM CYCLE
Fva1 Fva1 Fva1 Fva1 ALARM 1 FUNCTION: Select options from Table 3.
Fva2 Fva2 Fva2 Fva2 ALARM 2 FUNCTION: Select options from Table 3.
Fva3 Fva3 Fva3 Fva3 ALARM 3 FUNCTION: Select options from Table 3.
Fva4 Fva4 Fva4 Fva4 ALARM 4 FUNCTION: Select options from Table 3.
bla1 bla1 bla1 bla1
bla2 bla2 bla2 bla2
bla3 bla3 bla3 bla3
bla4 bla4 bla4 bla4
ALARM BLOCK 1 TO 4: This function blocks the alarm at
power-up when the units is first energized.
YES enables and NO inhibits this blocking function. When
enabled the alarm will not be active at power-up waiting for
PV (Process Variable) to reach a non-alarm situation. From
this point on the alarm will be free to actuate should a new
alarm situation occur.
xya1 xya1 xya1 xya1
xya2 xya2 xya2 xya2
xya3 xya3 xya3 xya3
xya4 xya4 xya4 xya4
ALARM HYSTERESIS: Defines the differential range
between the PV value at which the alarm is turned on and
the value at which it is turned off (in engineering units).
A1t1 A1t1 A1t1 A1t1 ALARM 1 TIME 1: Defines the time (6500 sec. max.)
during which the alarm 1 output will be ON when alarm 1 is
active. Program zero to disable this function.
A1t2 A1t2 A1t2 A1t2 ALARM 1 TIME 2: Defines the OFF state time for the
alarm 1 output, after being ON during the time selected on
ALARM 1 TIME 1. Program zero to disable this function.
A2t1 A2t1 A2t1 A2t1 ALARM 2 TIME 1: Defines the time (6500 sec. max.) during
which the alarm 1 output will be ON when alarm 1 is active.
Program zero to disable this function
A2t2 A2t2 A2t2 A2t2 ALARM 2 TIME 2: Defines the time during which the alarm
2 output will be, after being ON during the time selected on
ALARM 2 TIME 1. Program zero to disable this function.
Table 4 shows the advanced features that can be achieved
with these time functions.