AEM 30-3812 Infinity Plug & Play Harnesses - Ford Coyote to Ford Racing Controls Pack - Manual (Page 14)

14
© 2014 AEM Performance Electronics
P/N 30-3812
E - 53 (INJ1) hold, 3A max continuous
C1-64 +12V
Ford
Racing
PCM70 -
67 and
AUX - 8
+12V In 12 volt power from relay
12 volt power from relay. Relay must
be controlled by +12V Relay Control
signal pin C1-29 above.
C1-65 +12V_SW
Ford
Racing
PCM70 -
42
12V Start & Run (ISP-
R) Blunt Lead
10K pulldown
Full time battery power must be
available at C1-10 before this input
is triggered.
C1-66
Analog_In_Temp
_1
Engine
E - 30
Cylinder Head
Temperature (CHT)
12 bit A/D, 2.49K pullup
to 5V
See 'Coolant Temperature' Setup
Wizard for selection.
C1-67
Analog_In_Temp
_2
Ford
Racing
PCM70 -
47 and
AUX -2
Intake Air
Temperature
12 bit A/D, 2.49K pullup
to 5V
See 'Air Temperature' Setup Wizard
for selection.
C1-68
Analog_In_Temp
_3
---
Oil Temperature
Sensor
12 bit A/D, 2.49K pullup
to 5V
See 'Oil Temperature' Setup Wizard
for selection.
C1-69 Stepper_2A --- Stepper 2A
Automotive,
Programmable Stepper
Driver, up to 28V and
±1.4A
Be sure that each internal coil of the
stepper motor are properly paired
with the 1A/1B and 2A/2B ECU
outputs. Supports Bi-Polar stepper
motors only. See Setup Wizard page
'Idle - Show Advanced Setup' for
options.
C1-70 Stepper_1A --- Stepper 1A
Automotive,
Programmable Stepper
Driver, up to 28V and
±1.4A
Be sure that each internal coil of the
stepper motor are properly paired
with the 1A/1B and 2A/2B ECU
outputs. Supports Bi-Polar stepper
motors only. See Setup Wizard page
'Idle - Show Advanced Setup' for
options.
C1-71 Stepper_2B --- Stepper 2B
Automotive,
Programmable Stepper
Driver, up to 28V and
±1.4A
Be sure that each internal coil of the
stepper motor are properly paired
with the 1A/1B and 2A/2B ECU
outputs. Supports Bi-Polar stepper
motors only. See Setup Wizard page
'Idle - Show Advanced Setup' for
options.
C1-72 Stepper_1B --- Stepper 1B
Automotive,
Programmable Stepper
Driver, up to 28V and
±1.4A
Be sure that each internal coil of the
stepper motor are properly paired
with the 1A/1B and 2A/2B ECU
outputs. Supports Bi-Polar stepper
motors only. See Setup Wizard page
'Idle - Show Advanced Setup' for
options.
C1-73 Power Ground
Ford
Racing
PCM70 -
70
PWR Ground Power Ground Connect directly to battery ground
C2-1 DBW2 Motor + --
DBW Motor Control
Open
5.0A max Throttle
Control Hbridge Drive
+12V to open
C2-2 DBW2 Motor - --
DBW Motor Control
Close
5.0A max Throttle
Control Hbridge Drive
+12V to close
C2-3 Power Ground -- Ground Power Ground Connect directly to battery ground