AEM 30-3812 Infinity Plug & Play Harnesses - Ford Coyote to Ford Racing Controls Pack User Manual
Page 23
Ford Coyote 5.0L V8
23
© 2014 AEM Performance Electronics
31
---
---
---
---
---
32
AGND_1
C1-20
Digital Cams
Ground (E-SIGRTN)
Dedicated analog
ground
Analog 0-5V sensor ground
33
34
Coil 5
4P "Coil Driver
2" - 4
Ignition Coil on Plug
Assembly 5 (COP5B)
25 mA max source
current
0-5V Falling edge fire. DO NOT
connect directly to coil primary.
Must use an ignitor OR CDI that
accepts a FALLING edge fire signal.
35
---
---
---
---
---
36
+12V
C1-61 and
Ford Racing
PCM70-21
Digital Cam Sensor
+12V Power
12 volt power from
relay
12 volt power from relay. Relay
must be controlled by +12V Relay
Control signal, pin C1-29 above.
37
---
---
---
---
---
38
---
---
---
---
---
39
Analog_In_7
C1-35
DBW Negative
Slope (TP1)
12 bit A/D, 100K pullup
to 5V
0-5V analog signal. Use +5V Out pins
as power supply and Sensor Ground
pins as the low reference. Do not
connect signals referenced to +12V
as this can permanently damage
the ECU. See the Setup Wizard Set
Throttle Range page for automatic
min/max calibration. Monitor the
Throttle [%] channel. Also DB1_TPSA
[%] for DBW applications.
40
---
---
---
---
---
41
Camshaft Position
Sensor 1 Hall
C1-22
Camshaft Position
Bank 1 (Passenger
Intake) (CMP11)
10K pullup to 12V. Will
work with ground or
floating switches.
See Setup Wizard page 'Cam/Crank'
for options.
42
Digital_In_2
C1-23
Camshaft Position
Bank 2 (Driverside
Intake) (CMP21)
10K pullup to 12V. Will
work with ground or
floating switches.
See Setup Wizard page 'Cam/Crank'
for options.
43
---
---
---
---
---
44
AGND_2
C2-31 and
Engine E-6
Knock Sensor 2
Ground [KS2 -]
Dedicated analog
ground
Analog 0-5V sensor ground
45
Knock Sensor 2
C1-28
Knock Sensor+ [KS2
+]
Dedicated knock signal
processor
See Setup Wizard page 'Knock Setup'
for options.
46
Camshaft Position
Sensor 1 VR+
C1-48
Camshaft Position
Bank 1 In
(Passenger side
Exhaust) (CMP12)
Differential Variable
Reluctance Zero Cross
Detection
See Setup Wizard page 'Cam/Crank'
for options.
47
VR+_In_2
C1-49
Camshaft Position
Bank 2 In (Driver
side Exhaust)
(CMP22)
Differential Variable
Reluctance Zero Cross
Detection
See Setup Wizard page 'Cam/Crank'
for options.
48
VR-_In_2
C1-50
Variable
Reluctance Sensor
(VRSRTN2)
Differential Variable
Reluctance Zero Cross
Detection
See Setup Wizard page 'Cam/Crank'
for options.
49
---
---
---
---
---
50
Coil 4
4P "Coil Driver
1" - 1
Ignition Coil On Plug
Assembly 4 (COP-D)
25 mA max source
current
0-5V Falling edge fire. DO NOT
connect directly to coil primary.
Must use an ignitor OR CDI that
accepts a FALLING edge fire signal.