Comelit MT 8172IS - Manual (Page 31)

31 31
EN
Take note of the S2, S1 setting and restore it when programming is complete
1) 2) 3) 4)
S1
DIP
1
DIP
2
DIP
3
DIP
4
DIP
5
DIP
6
S2 S1/S2/LED1
1 1 1 1 1 1
‰
4AKEæ NOTEæ OFæ THEæ
S2, S1
SETTINGæANDæ
RESTOREæ ITæ WHENæ
PROGRAMMINGæ
ISæ
COMPLETE
Factory settings:
sæ"UTTONæFUNCTIONSæFORæTHEæ3æ$)0æSWITCHæ


æCOMBINATION
sæ)NTERCOMæADDRESSæABSENT
sæ2ANGEæFUNCTIONæANDæMINMAXæADDRESSESæABSENT
sæ2INGTONEæRESET
sæ)NPUTæ).жж‰ж,%$жDEFAULT 
DIP ON
2
‰
1
KO Prog.
5 sec
OK Prog.
Programming reset
!LLOWSæDIRECTæPROGRAMMINGæOFæINTERCOMæCALLæVIAæTHEæINTERNALæUNITS
√ 2EQUIRESææOPERATORS
Step 1: enter programming mode
Operator 1 and Operator 2 carry out the following procedures
on 2 internal units:
æ3ETж3ж$)0æSWITCHESæ
æ

æTOæTHEæCOMBINATIONæ
æ0RESSæANDæHOLDæBUTTONSæææANDææFORææSEC
»The internal unit emits 1 tone.
»The red LED flashes.
»The blue audio LED lights up.
»The internal unit enters audio mode.
»At this point the 2 operators will be communicating with each
other.
____
Step 2 (optional): intercom audio volume adjustment
æ!DJUSTæTHEæINTERCOMæAUDIOæVOLUMEæUSINGæTHEæAUDIOæADJUSTMENTæKNOBææ
æ0RESSæKEYæææ A TOæCONlRM
»The internal unit emits 1 tone.
»The blue lock-release LED flashes.
»The monitor memorises the audio setting for intercom calls.
æ!Tæ THEæ ENDæ OFæ THEæ AUDIOæ ADJUSTMENT æ SETæ THEæ EXTERNALæ UNITæ AUDIOæ
VOLUMEæADJUSTMENTæKNOBææ æBACKæTOæITSæPREVIOUSæPOSITION
Direct programming of intercom call
_____________________
Step 3: intercom call programming
Operator 1:
` 0RESSæTHEæBUTTONæYOUæWANTæTOæPROGRAMæTOæCALLæOPERATORææEGæ 
»The internal unit manned by operator 1 emits a confirmation tone.
Operator 2:
` 0RESSæTHEæBUTTONæYOUæWANTæTOæPROGRAMæTOæCALLæOPERATORææEGæ 
»The internal unit manned by operator 2 emits a confirmation tone.
Operator 1/Operator 2:
` 0RESSæTHEæBUTTONæ 
»The blue audio LED switches off.
»Programming of the 2 internal units is now complete.
4OæPROGRAMæANOTHERæINTERNALæUNIT æMOVEæONæTOæ34%0æ
____
Step 4: programming other internal units
Operator 1/Operator 2:
 /NCEæ THEæ NEWæ STATIONæ HASæ BEENæ REACHED æ CARRYæ OUTæ STEPæ æ TOæ
BEGINæCOMMUNICATION
æ2EPEATæSTEPæ æ
NOTE )FæAæCALLæISæRECEIVEDæDURINGæPROGRAMMING æITæMUSTæBEæANSWEREDæ
ANDæTHEæPROGRAMMINGæPROCEDUREæRESUMEDæAFTERWARDS