EUCHNER MGB-L2-xxxAPx-xxx - Manual (Page 33)

33
Operating Instructions MGB-L1...AR.-... / MGB-L2...AR.-... and MGB-L1...AP.-... / MGB-L2...AP.-...
13.2 System status table MGB-AR
Operating mode
Safety inputs
FI1A and FI1B
Door position
Position of the bolt
tongue
Guard locking
Safety outputs FO1A and
FO1B
Door monitoring
output (OD)
Monitoring output
bolt tongue (OT)
Guard locking monitoring
output (OL)
Diagnostics
monitoring output (OI)
LED indicator
State
Power (green)
STATE (gr een)
DIA (red)
Lock (yellow)
Self-test
X
X
X
X
OFF
OFF
OFF
OFF
OFF
5 Hz
Self-test after power up
Normal operation
X
open
not inser
ted
OFF
OFF
OFF
OFF
OFF
OFF
Long OFF shor
t ON
Normal operation, door open
X
closed
not inser
ted
OFF
OFF
ON
OFF
OFF
OFF
Long ON, shor
t OFF
Normal operation, door closed
OFF
closed
inser
ted
OFF
OFF
ON
ON
OFF
OFF
Long ON, shor
t OFF
Long ON, shor
t OFF
Normal operation, door closed, bolt tongue inser
ted safety inputs FI1A/FI1B OFF
ON
closed
inser
ted
OFF
OFF
ON
ON
OFF
OFF
Long ON, shor
t OFF
Long ON, shor
t OFF
W
ith active guar
d lock monitoring:
Normal operation, door closed, bolt tongue inser
ted. Safety
inputs FI1A/FI1B ar
e ON. Safety outputs FO1A and FO1B ar
e OFF
ON
W
ith inactive guar
d lock monitoring:
Normal operation, door closed, bolt tongue inser
ted.
Safety inputs FI1A/FI1B ar
e ON. Safety outputs FO1A and FO1B ar
e ON
OFF
closed
inser
ted
ON
OFF
ON
ON
ON
OFF
Long ON, shor
t OFF
Operation in an AR chain:
Normal operation, door closed and locked. Safety outputs on the
pr
evious device OFF
ON
closed
inser
ted
ON
ON
ON
ON
ON
OFF
Operation as separate device:
Normal operation, door closed and locked.
Operation in an AR chain:
Normal operation, door closed and locked. Safety outputs on the
pr
evious device ON
Teach-in standby (only for MGB unicode)
X
open
not inser
ted
OFF
OFF
OFF
OFF
OFF
OFF
3 x
Door open; unit is r
eady for teach-in for another handle module (only 3 min. after power-up)
Setup (only for MGB unicode)
X
closed
inser
ted
ON
OFF
OFF
OFF
OFF
OFF
2 Hz
Teach-in operation, tip: T
o pr
event the interruption of teach-in operations, close door and switch on
guar
d locking.
X
X
X
X
OFF
OFF
OFF
OFF
OFF
Positive acknowledgment after completion of teach-in operation
Diagnostics
X
X
X
X
OFF
OFF
OFF
OFF
ON
1 x
Err
or during teach-in / configuration or invalid DIPswitch setting
err
one
-
ous
X
X
X
OFF
OFF
OFF
OFF
ON
2 x
Input err
or (e.g. missing test pulses, illogical switch state fr
om pr
evious switch)*
X
X
X
X
OFF
X
X
X
OFF
3 x
:Handle module r
ead err
or (e.g. err
or in code)**
X
X
X
X
OFF
OFF
OFF
OFF
ON
4 x
Output err
or (e.g. shor
t cir
cuits or loss of switching capability) or shor
t cir
cuit at the outputs*
X
X
X
X
OFF
OFF
OFF
OFF
ON
Internal fault (e.g. component faulty
, data fault)*
X
X
X
X
OFF
OFF
OFF
OFF
ON
1 x
Signal sequence err
oneous (e.g. br
oken bolt tongue) ***
W
ith active r
elease monitoring: escape r
elease or mechanical r
elease was actuated
X
X
X
X
X
X
X
X
X
Power is ON for a very long time with shor
t
interruption
1 million operating cycles exceeded
*
Latching fault; to r
eset, use the RST input or briefly disconnect the device fr
om the power supply
**
Non-latching fault; open safety guar
d and close it again to r
eset
***
See section
14 T
roubleshooting and assistance, page 35
Impor
tant
: If you do not find the displayed device status in the System status table, this indicates an internal device fault. In this case, you should contact the manufactur
er
.