FasTest TwistMate Serie - Manual

OPERATING INSTRUCTIONS
www.fastestinc.com
Roseville, MN
Ph 1-800-444-2373
Fax 651-645-7390
PAT# 4,688,830 WP096 10/7/2010
FINGER TIGHT THREAD IN ACTUATION
CUSTOMER TEST
PIECE
MAIN SEAL
TEST PRESSURE
PRESSURE
PISTON / SLEEVE
CUSTOMER TEST
PIECE
MAIN SEAL
FEMALE TEST PRESSURE
CONNECTION PORT
PRESSURE
PISTON / SLEEVE
MAIN SEAL SLEEVE
BACK-UP
RING
BACK-UP
O-RING
BODY
FINGER TIGHT THREAD IN ACTUATION
MIT CONNECTOR
WRENCH FLATS
MIT / MITH Connectors
DESCRIPTION: Quick connectors for Female Threads.
Note: Shown to the right is the THREADED MALE SWIVEL CONNECTOR.
Swivel connector operates the same as the
THREADED MALE CONNECTOR shown above.
Please thoroughly read the instructions prior to operating the connector. The connectors are
designed to provide a safe, reliable leak-tight seal and connection when properly maintained and operated.
• The connector is designed to mate with a specific application. Verify the application prior to the
introduction of pressure or processing. Use only in a safe environment. Safety chains and guards are
recommended for all applications.
• Connectors are NOT designed for permanent connections and are for temporary connections only.
Inadvertent loosening and loss of media may result when used as a permanent connection.
• Connectors are not internally valved and will not prevent loss of media when disconnected.
DO NOT EXCEED pressure rating as marked on connector or corresponding literature. Operating pressure
rating based on tests using NPTF threads (to SAE J476a Dryseal specifications) of cold drawn steel. Material
or thread deviations may reduce working pressure and should be verified by test.
OPERATION:
1. Fasten connector securely to pressure supply line or manifold by threading
connector wrench-tight using wrench flats on body or hex flats on swivel unit.
NOTE: Plug style connectors do not require wrench-tightening.
2. Thread connector finger-tight onto test piece until Main Seal contacts test piece.
3. Introduce test pressure to . Connector will automatically seal when internal
pressure is applied.
4. Perform evacuation / filling operations.
5. To remove, release test pressure and thread off connector.
CONNECTOR MAINTENANCE:
• A daily, weekly and periodic inspection of the connector by competent person is recommended.
o User must establish a regular interval for maintenance as determined by the user media and
operational environment.
o Inspection should include damage to the body missing or loose components, leak tightness,
ease of operation, sufficient lubrication, wear, dirt accumulation and damage.
• Inspect threads for wear.
• Use only original FasTest spare parts that are designed for the application and are subject to strict
quality control. See warranty.
• FasTest recommends a daily visual inspection of the main seal located in the front of the sleeve.
Inspect for tears or cracks in the seal surface. Replace the main seal if tears or cracks are visible.
• Lubricate on regular intervals under normal operating conditions. Lubrication should be compati-
ble with user application.
FasTest, Inc. Product Warranty
FasTest, Inc. warrants its products against defects of workmanship and/or material for 12 months from the date of the sale by FasTest,
Inc. This warranty is void if the product is misused, tampered with or used in a manner that is not in accordance with FasTest, Inc.
recommendations and/or instructions. FasTest, Inc. is not liable for consequential or other damages including, but not limited to, loss,
damage, personal injury, or any other expense directly or indirectly arising from the use of or inability to use its products either
separately or in combination with other products. ALL OTHER WARRANTIES EXPRESSED OR IMPLIED, WHETHER ORAL OR
WRITTEN, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE ARE EXPRESSLY EXCLUDED.
Remedy under this warranty is limited to replacement of the product or an account credit in the amount of the original selling price, at
the option on FasTest, Inc. All allegedly defective products must be returned prepaid transportation to FasTest, Inc. along with
information describing the products performance, unless disposition in the field is authorized in writing by FasTest, Inc.
PLUG MALE
CONNECTOR STYLE
THREADED MALE
CONNECTOR STYLE