Great Plains Gauge Wheel-Spindle - Manual (Page 23)

Great Plains Mfg., Inc.
Installation Instructions 23
04/10/2009 195-080M
The following existing parts are involved in the kit instal-
lation. The Disposition column indicates whether the part
is left in place, moved or not re-used.
The part call-out numbers in the list matches all Figures
in the installation instructions. The general descriptions
match those in your drill Parts manual.
The part numbers are representative of parts found on
older drills, but may not exactly match those on your drill.
This is not a concern for undamaged parts re-installed or
not re-used at all. If you need to replace any parts not in
the kit, older the current part number called for in the lat-
est Parts manual.
Abbreviations
Callout
Typical
Part No.
Typical Part Description Part Disposition
120-198D AXLE SPACER TUBE Removed and re-installed.
152-390D 6-BOLT HEAVY DRIVE HUB 2 BORE Removed and re-installed.
161-046K 6 BOLT WHL&TIRE 8 PLY TUBELESS Removed and re-installed.
195-229D SPNDLE 2"W/5/8 CROSS HOLE DUAL Removed. Not re-used.
195-234D WASHER FLAT 2 ID X 2 5/8 X 10G Removed. May be re-installed.
802-104C BOLT WHEEL 1/2-20X1 90-DEG Removed and re-installed.
802-687C HHCS 5/8-11X4 SPTHD GR8 Removed and re-installed.
803-208C NUT BRG LOCK, TN-10 Removed. Not re-used.
803-239C NUT HEX SLOTTED 1 1/2-12 PLT Removed and re-installed.
803-263C NUT HEX FLANGE LOCK 5/8-11 PLT Removed and re-installed.
804-095C WASHER FLAT 5/8 HARD ASTMF436 Removed and re-installed.
804-098C WASHER BRG LOCK, TW110 Removed. Not re-used.
804-182C WASHER HARD 1 1/2 MILCARB GR8 Removed and re-installed.
805-030C PIN ROLL 5/16 X 3 PLT Removed. Not re-used.
805-148C PIN COTTER 3/8 X 3 PLT Removed. Not re-used.
808-287C SPKT 50B19C2B W/5/16 HOLE Removed. Not re-used.
816-012C SEAL 3.375 X 2.0 X.438 CR20125 Removed. Not re-used.
816-138C SEAL DBL LIP 2.5 ID X 3.881 OD Removed. Not re-used.
822-117C BRG CONE 2.00ID TIM33889 Removed and re-installed.
822-118C BRG CUP 3.75OD TIM33821 Re-installed if removed
10G Ten Gauge MILCARB Military Standard Carburized
2S Two Section MIN Minimum
3S Three Section NHS Non-Highway Service
ASTM American Society for Testing and Materials NOHLE No Hole
BLT Bolt OD Outside Diameter
BRG Bearing PILT Pilot
CR Chicago Rawhide (SKS brand) PLT Plated
DBL Double PSI Pounds per Square Inch
DEG Degree
DRV Drive RH Right Hand
FLG Flanged SKID ST Skid Steer
FT Foot (-Pounds) SPNDL Spindle
GR8 Grade 8 SPTHD Special Thread
GW Gauge Wheel THD Thread
HD Heavy Duty TIM Timken (brand)
HEX Hexagonal TN Timken (bearing) Nut
HHCS Hex Head Cap Screw (Bolt) TUBLES Tubeless
ID Inside Diameter TW Timken Washer
IN Inch W/ with
LG Long WHL Wheel
LH Left Hand X by
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70