Great Plains 2N-3010 Parts Manual - Manual (Page 149)

Revision Comments Part Description Part No. Ref.
Image No. dwg16065
2nd rev. For 3010 drills. (S/N D2107, D2109,
and D2110+) Refer to "Midway
Hydraulic Cylinder (810-394C)" for
breakdown.
HYD CYL REP 4 X 12 X 1 1/2 ROD 810-394C 1.
2nd rev. For 2410 drills. (S/N C1824) Refer to
"Midway Hydraulic Cylinder
(810-395C)" for breakdown.
HYD CYL REP 3 3/4 X 12 X 1 1/2 810-395C 1.
1st rev. Refer to "Midway Hydraulic Cylinder
(810-123C)" for breakdown. For 3010
drills.
CYL REP 4.25X12X1.5ROD(TIE)1PN 810-123C 1.
1st rev. Refer to "Midway Hydraulic Cylinder
(810-222C)" for breakdown. For 2410
drills.
CYL REP 4X12X1.37 ROD (TIE) 810-222C 1.
30' Drill HH1/2R2 218 3/4FJIC 3/4MORB90 811-455C 2.
24' Drill HH1/2R2 185 3/4FJIC 3/4MORB90 811-468C 2.
AD 3/4MORB 3/4MJIC 811-088C 3.
TE 3/4MJIC 811-078C 4.
30' Drill HH1/2R2 400 1/2MNPT 3/4FJIC 811-482C 5.
24' Drill HH1/2R2 365 1/2MNPT 3/4FJIC 811-484C 5.
EL 3/4MJIC 3/4MORB 811-063C 6.
TE 3/4MORB 3/4MJIC 3/4MJIC 811-077C 7.
2nd rev. For 3010 drills. (S/N D2107, D2109,
and D2110+) Refer to "Midway
Hydraulic Cylinder (810-393C)" for
breakdown.
HYD CYL 4 1/2 X 12 X 2 ROD 810-393C 8.
2nd rev. For 2410 drills. (S/N C1824+) Refer to
"Midway Hydraulic Cylinder
(810-392C)" for breakdown.
HYD CYL 4 1/4 X 12 X 2 ROD 810-392C 8.
1st rev. Refer to "Midway Hydraulic Cylinder
(810-218C)" for breakdown. For 3010
drills.
CYL REP 4.5X12X1.5 ROD (TIE) 810-218C 8.
1st rev. Refer to "Midway Hydraulic Cylinder
(810-221C)" for breakdown. For 2410
drills
CYL REP 4.25X12X1.5 ROD (TIE) 810-221C 8.
HH1/2R2 030 3/4FJIC 811-340C 9.
HH1/2R2 472 1/2MNPT 3/4MORB 811-575C 10.
HH1/2R2 435 1/2MNPT 3/4MORB 811-576C 10.
TRANSPORT CYLINDER JUMPER TUBE 811-400C 11.
24' Drill HH1/2R2 218 3/4FJIC 3/4MORB90 811-455C 12.
30' Drill HH1/2R2 250 3/4FJIC 3/4MORB90 811-629C 12.
CABLE TIE .31X21.5 6DIA 120LB 800-082C 13.
(S/N C1890+ 24' S/N D2275+ 30') CP 1/2FNPT MALE QD 811-856C 14.
01/31/14 - 149 - 196-126P Rev. A
Table of Contents Part Number Index
Hydraulics
Transport Axle And Gauge Wheel Hydraulics (S/N C1693+ 24' Drills S/N
D1905+ 30' Drills)
(Applies to 2N-2410 (1995+), 2N-3010 (1995+) only)