Great Plains 2N-3010 Parts Manual - Manual (Page 85)

Revision Comments Part Description Part No. Ref.
Image No. dwg16050
NUT HEX 1 1/4-7 PLT 803-034C 1.
WASHER LOCK 1 1/4 SPRING PLT 804-030C 2.
NUT HEX JAM 1 1/4-7 PLT 803-032C 3.
BRG 3.25 3-HL FLG DRIVE 172-206D 4.
SNAP RING INT. 2.05 OD 800-038C 5.
BEARING 1.000 DIA W/SET-SCREWS 188-003V 6.
Includes Items 4; 5 & 6 GAUGE WHEEL PIVOT BUSHING ASSY 152-074S 7.
ACRE METER 30' 890-012C 8.
ACRE METER 24' 890-002C 8.
HHCS 5/8-11X3 GR5 802-059C 9.
24' (S/N C1851- 30' S/N D2183-) 2SNT CHAIN GUARD WELDMENT 152-091H 10.
AXLE BUSHING BRACE WELDMENT 152-134H 11.
WASHER LOCK SPRING 5/8 PLT 804-022C 12.
NUT HEX 5/8-11 PLT 803-021C 13.
BOLT WHEEL 1/2-20X1 90-DEG 802-104C 14.
WHEEL 8 X 15 X 6 BOLT 814-008C 15.
TIRE 11L-15 X 8 PLY 814-038C 16.
VALVE STEM TR415X.625X1 1/4 LG 816-035C 17.
Includes items 15; 16 & 17 RPBY 197-148K 120-218K 18.
2nd Revision For 3010 Drills. (S/N D2107, D2109
and D2110+) Refer to page 9-37 for
breakdown
HYD CYL REP 4 X 12 X 1 1/2 ROD 810-394C 19.
2nd Revision For 2410 Drills. (S/N C1824) Refer to
page 9-33 for breakdown
HYD CYL REP 3 3/4 X 12 X 1 1/2 810-395C 19.
1st Revision Refer to page 9-39 for breakdown for
3010 Drills.
CYL REP 4.25X12X1.5ROD(TIE)1PN 810-123C 19.
1st Revision Refer to page 9-35 for breakdown for
2410 Drills.
CYL REP 4X12X1.37 ROD (TIE) 810-222C 19.
BUSHING CYL 1 1/4 X 1 X 1 890-005C 20.
EYEBOLT WELDMENT 196-142H 21.
WASHER FLAT 1 SAE 804-029C 22.
2SNT AXLE BUSHING BRACE PLATE 152-109D 23.
2nd Revision GREASE ZERK 1/4-28 X 45-DEG 800-058C 24.
1st Revision CHAIN RL #40 126 PITCHES 136-112D 25.
RPBY 136-112D 809-153C 25.
HHCS 5/8-11X2 3/4 GR5 802-281C 26.
CLUTCH ENGAGE TAB 152-263D 27.
HHCS 3/8-16X1 1/4 GR5 802-079C 28.
WASHER FLAT 3/8 SAE PLT 804-012C 29.
WASHER LOCK SPRING 3/8 PLT 804-013C 30.
NUT HEX 3/8-16 PLT 803-014C 31.
WASHER FLAT 1 SAE 804-029C 32.
24' S/N C1852+ 30' S/N D2184+ SPLINED ACREMETER MOUNT 890-849C 33.
24' S/N C1852+ 30' S/N D2184+ SNAP RING EXT F/PEERLESS G.B. 800-141C 34.
24' S/N C1852+ 30' S/N D2184+ ACREMETER HUB WELDMENT 197-164H 35.
24' S/N C1852+ 30' S/N D2184+ HHCS 1/4-20X5/8 GR5 802-078C 36.
24' S/N C1852+ 30' S/N D2184+ WASHER FLAT 1/4 SAE PLT 804-007C 37.
01/31/14 - 85 - 196-126P Rev. A
Table of Contents Part Number Index
Drives
Gauge Wheel (Continued)
(Applies to 2N-2410 (1995+), 2N-3010 (1995+) only)