Sony LBT-D570 - Manual (Page 15)

One Touch Play feature
Press O or [> (or DECK A O /DECK B
O on the remote) when the power is off.
When a tape is in the player, you will
immediately be able to listen to the tape
without pressing any other buttons. If no
tape is inserted, the system will just turn
on.
The tape player always starts playing from
the front side of the tape when you operate
the remote.
Recording a CD
You can record from a CD to a tape. Use
TYPE I (normal) or TYPE II (CrCh) tapes.
You can not listen to other sources while
recording.
Recording a CD
automatically
By using CD SYNCHRO, you can record
from a CD to a tape easily.
Use the buttons on the unit for this
operation.
SYSTEM
POWER-»ON
T
o
•
l~l I I I I I ’—’ I I tl t
1 Press FUNCTION repeatedly imtil
"CD" appears in the display.
2
Press = OPEN and place a CD on the
tray.
Make sure the disc number in the
playing position in the display is the one
you want to record.
The total number of tracks and the
playing time appear in the display.
3
Press a EJECT and insert a blank tape
into deck B with the side you want to
record on facing forward.
Recording starts from the front side of
the tape, unless you change the playing
direction before recording.
Make sure the tabs on the cassette have
not been removed.
4
Select dual or single- sided recording.
To record Press DIRECTION to
select
One side of the
tape
Both sides* or RELAY
* Recording always stops at the end of the
reverse side. Be sure to start from the
front side.
5
When you want to reduce the hiss noise
in low-level high-frequency signals, ,
Press DOLBY NR so that "DOLBY NR
B" appears in the display.
6
Press CD SYNCHRO.
The REC and DD (pause) lamps light up
and deck B stands by for recording.
The O lamp lights up and the <I lamp
flashes for a few seconds, then
disappears.
r
Side in recording
pause mode
If you want to start recording from the
. reverse side, press <1 so that the <1
lamp lights steadily.
7
Press OD on the tape player to release
recording pause.
Recording starts.
After about 10 seconds, the CD starts
playing.
To stop recording
Press □ on the tape player or the CD
player.
To record with surround effect
Press SURROUND so that "SUR "
appears in the display.
The equalizer you have adjusted will not be
recorded.
Recording a CD Manually
You can record a CD as you like, for
example, record just the songs you want or
record from the middle of the tape.
9
8
4
7
3
10
6
1
Press FUNCTION repeatedly until
"CD" appears in the display.
2
Press = OPEN and place a CD on the
tray.
Make sure the disc number in the
playing position in the display is the one
you want to record.
The total number of tracks and the
playing time appear in the display.
3
Press = EJECT and insert a blank tape
into deck B with the side you want to
record on facing forward.
Recording starts from the front side of
the tape, unless you change the playing
direction before recording.
Make sure the tabs on the cassette have
not been removed.
4
Select dual or single-sided recording.
To record Press DIRECTION to
set
One side of the
tape
Both sides* or RELAY
* Recording always stops at the end of the
reverse side. Be sure to start from the
front side.
5
If you want to record a specific track of
the CD, press DD on the CD player.
The CD player pauses for playing.
If you do not need to choose a track,
skip to step 7.
6
Turn the JCXS dial to choose the track
you want to record.
7
When you want to reduce the hiss noise
in low-level high-frequency signals.
Press DOLBY NR so that "DOLBY NR
B" appears in the display.
continue to next page -»
Chapter 4: the Tape Player I »j ^