Panasonic WJ-SQ508 - Manual (Page 6)

20. Program Switch (PROGRAM)
This switch is a push - push type switch with LED
indicator. While the LED of this switch is on, the
programmed sequential switching which has been
previously set will be performed. To cancel the
programmed sequential mode, press this switch and
turn the LED off.
21 . Video Input Connectors (VIDEO IN 1/2- -/ 8 )
These connector accept either FM (audio) mixed video
signals or standard video signals.
22. Alarm/ Sequence Video Output Connector
(ALARM/SEQ VIDEO OUT)
The standard composite video signal is provided at this
connector. When the WJ-SQ508 is in the sequential
mode, either the normal sequence or programmed
sequence, the sequential video signal is provided at this
connector. When the WJ-SQ508 is in the alarm mode,
the alarmed video signal is provided at this connector.
Note:
A Time Lapse VTR is recommended for use with
this connector.
23. Spot/Sequence Video Output Connector
(SPOT/SEQ VIDEO OUT)
The FM (audio) mixed video signal is provided at this
connector. When the WJ-SQ508 is in the sequential
mode, either the normal sequence or the programmed
sequence, the FM (audio) mixed sequential video signal
is provided at this connector. When the WJ-SQ508 is
in the spot mode, the FM (audio) mixed spot video signal
is provided at this connector.
Note:
1. An audio beat noise will be seen on the video
monitor when the FM (audio) mixed video signal
is supplied from this connector. Turn the
Spot/Sequence Audio Switch (26) to the OFF
position to eliminate the audio beat noise.
2, The video input of WV-CU300 accepts the
FM (audio) mixed video signal from the
Spot/Sequence Video Output Connector (23) of
the WJ-SQ508 without audio beat noise.
24. Spot/Sequence Video Slave Input Connector
(SPOT/SEQ VIDEO SLAVE IN)
This connector accepts the FM (audio) mixed
video signal from the Spot/Sequence Video Output
Connector (23) of another WJ-SQ508 in a master-slave
operation.
25. Alarm/Sequence Video Slave Input Connector
(ALARM/SEQ VIDEO SLAVE IN)
This connector accepts the video signal from the
Alarm/Sequence Video Output Connector (22) of
another WJ-SQ508 in a master- slave operation
26. Spot/Sequence Audio Switch
(SPOT/SEQ AUDIO ON/OFF)
The audio signal on the spot/sequence video output
signal will be cut off when this switch is in OFF position.
If the audio sound is not necessary during a sequential
operation with a WV-CU300, turn this switch off. When
this switch is in ON position, the sequential switching
audio signal as well as the video signal will be obtained
at the WV-CU300.
27. Master/Slave Switch (MASTER/SLAVE)
This switch should be properly set when using the
master- slave operation of the WJ-SQ508. Turn this
switch to the MASTER position when this WJ-SQ508
is used as the master unit and turn this switch to the
SLAVE position on all the others WJ-SQ508 that are
used as slave units.
Note:
Turn this switch to the Master position when this
unit is used alone.
28. Data Input /Output Connector (DATA IN/OUT 1 /2)
The control data transmitted from other system
components (WV-CU300, WJ-MP404 or WJ-SQ508)
is supplied to one of these connectors. If the control
data has to be sent to other system components, use
the other connector for it.
Note:
( 1 ) This connector is terminated by 750 automatically
when the BNC cable is connected.
(2) the data line should originate from WJ-MP404.
(Data Clock Switch to SND position) and should
loop through all necessary units. For additional
details see the WV-CU300 or WJ-MP404
operating instructions.
29. Station Number Selection Switch
(STATION NO. 1/2/3)
this switch is used to identify the station number of
each WJ-SQ508 in the system which branches out
from a WV-CU300.
Note:
Refer to the setting up of the station number on
page 12 .
30. Unit Number Selection Switch (UNIT NO. 1 - 8 }
This switch is used to identify the unit number of each
WJ-SQ508 in the system which branches out from a
WV-CU300.
Note:
1 , The NO. 0 and NO. 9 on this switch are of no use.
2. Refer to the setting up of the unit number on page
12 .
31. External Timing Output Connector
(EXT TIMING OUT)
The sequential switching interval of WJ-SQ508 can be
externally controlled by a Time Lapse VTR The timing
pulse from the External Timing Input Connector (32) is
provided to this connector for another WJ-SQ508.
Note:
When the Time Lapse VTR is not used with this
unit, the timing pulse set by the Dwell Time Control
(5) is provided to this connector.
- 5 -