Panasonic CF-25 User Manual
Panasonic Notebooks
Advertising
Table of contents
Document Outline
- Customer's Record
- Saving Data on the Hard Disk
- Saving Data on Floppy Disks
- Computer Viruses
- Other Precautions
- Starting Up
- Using the Touch Pad
- Shutting Down (power off your computer)
- Starting Up Your Computer Quickly
- Differences between the suspend function and hibernation function
- Using the hibernation function
- 1 Run the Setup Utility (o= page 40)
- 2 Using O and g), select [Power Management], then press
- 3 Using [[^ and select [Power Switch], set [Hibernation] with Q, then press
- 4 Close the Setup Utility page 40)
- Resuming Operation
- Conserving Power
- Things to Remember
- # Leave your computer off when it is not in use (opage io)
- Adjust the brightness (dark) with
- Before stepping away from your computer, press Q + @ to put your computer in the standby mode
- tn the power management mode, the setting of [Advanced] is recommended (opage 13)
- Setting the hibernation timeout (o-page 13)
- Setting Power Management
- (How to set [Advanced] and the hibernation timeout)
- 7 Run the Setup Utility (^ page 40)
- fusing 1^ and (§, select [Power Management], then press g
- 3 Using [§ and select [Power Saving], then set [Advanced] with Q
- 4 Using @ and ¡§, select [Power Switch], then set [Hibernation] with Q
- 5 Using @ and [§, select [Hibernation Timeout], set either [4 min] or [16 min] with then press
- Q Close the Setup Utility (q> page 40)
- ) Power Management settings
- Battery Status
- Use the Battery Indicator to Check on the Battery Status
- When the Remaining Battery Charge Becomes Low
- Precautions
- Replacing the Battery Pack
- When you do not want your computer to be used without permission
- Setting the Coffee break Password (enabling or disabling)
- Setting the Supervisor Password
- (enabling, changing, disabling)
- 1 Run the Setup Utility (c3= page 40)
- 2 Using [§ and (§, select [Supervisor Setup], then press
- 3 Using and O, select [Supervisor Password], then press
- 4 %To enable or change your supervisor password
- #To disable your supervisor password
- 5 Re-enter your password at the [Enter Supervisor Password Again]
- 6 Using @ and (§, select [Set Supervisor Password], then press
- 7 At the confirmation screen, press
- 8 Press r^T] to end the password setting procedure 8 Close the Setup Utility (c?* page 40)
- Preparations for Infrared Data Communications
- Running TranXit™
- Using a multimedia pocket device
- Installing/Removing a multimedia pocket device
- Using an External Display
- Power off your computer {^page 10)
- 3 Turn on the display, then turn on your computer
- #To display on both the LCD of your computer and the external display
- 1 Run the Setup Utility (cépage 40)
- 2 Using 1^ and select [System Setup], then press
- 3 Using [§ and (§, select [Display], set [Simultaneous] with (Q, then press fi^r]
- 4 Close the Setup Utility (o=page 40)
- 5 Select your external display
- Using a Printer
- Connecting a Port Replicator
- To change your hard disk, consult your nearest Panasonic Dealer or authorized Service Center
- Installing/Removing the hard disk
- Usage Environment
- Carrying
- Maintenance
- When flying
- CD-ROM
- List of Error Codes
- Using the Self-diagnosis Program
- y To run the program, insert the Firstaid FD you created into the floppy disk drive, then turn your computer on
- 2 When the display below is shown, select [1. Boot]
- 3 At the MS-DOS prompt (A:\WINDOWS\COMMAND>), input the following:
- • Starting Up
- Battery Indicator
- Character Input
- ^ Display
- Setup utility
- Connecting Peripherals
- Others
- Internet Explorer 4.0
- Reinstallation
- Power saving function in the sound chip
- Before Reinstallation
- Reinstalling
- Running the Setup Utility
- Closing the Proigram