Freerider FR510DXs2b(D,Land Ranger S) - Manual (Page 27)

a tyre or tube carry out the following instructions
(only competent people should carry out this procedure).
1. Switch off your Scooter and remove the key.
2. Using a suitable body stand, lift the side of the vehicle you
wish to service off the ground. Place the stand under
the metal chassis. Care must be taken when lifting heavy
loads, you may need a friend to help you. Care should
also be taken when working on a stand.
Please be safe. Do not lift by the plastic bodywork.
3. With the aid of a 19mm spanner (not supplied) remove
the centre hub nut and washer (see fig 33).
Slide the wheel from the mounting axle. Rear wheels are
fitted to the drive axle via a hub which locates onto a key.
4. These wheels fit tight onto the axle and may need some
pressure from a bearing puller onto the wheel hub to
release them from the axles. Look for spacing washers and
take care not to mislay the drive key which fits between the
wheel hub and the axle shaft.
5. First deflate the air from the wheel assembly by removing
the valve core from the valve with a suitable valve key
FIG 32
27
Safety Note: For your own safety, we recommend that you
check the function of your Scooter brakes prior to a journey.
If the motor brake is functioning correctly and
the drive is engaged you will not be able to push your
machine when it is switched off. Or switched on with the
speed control lever in the 'zero speed', central position.
If your machine can be pushed as described above, the motor
brake could be faulty, or the freewheel system has been
disengaged. Please do not use, contact your local distributor.
Note: Check the Freewheeling Instructions on page 12 of this
manual.
When you drive your
Scooter and you let go of the speed control lever your
Scooter should reduce speed very quickly. If you notice a
change in the normal slowing/braking condition, and your
Scooter does not slow down quickly, please do not use your
machine, contact your distributor.
The bearings which control the movement of the steering
handle bar may need to be adjusted if up and down
movement is noticed in your steering handle bars, and those
are accessed at the base of your handle bars.
The bearings are adjusted by first releasing the locking nut
anti-clockwise one full turn with a suitable spanner (Fig35).
Turn the upper bearing adjustment nut clockwise, one flat at
a time until all of the up and down movement in the handle
bars is removed. Retighten the lock nut clockwise into
position with a second spanner. Do not over tighten the
bearing adjustment nut, as this will damage the bearing tracks.
The handle bar bearings are NOT 'Sealed for life' and may
require lubrication with a general purpose bearing grease on
an annual basis.
TYRES
Check the condition of your tyres regularly. Look for signs of
wear, cuts and foreign objects lodged in the tread. Also,
maintain the tyre pressures at all times; failure to comply with
this can lead to poor performance of your machine and could
make your machine unsafe and/or unstable.
Your Scooter is designed with 'split' wheel rims.
Do not remove wheel bolts with the wheel inflated. Maintain
pneumatic tyres at 30 p.s.i. (210 kpa). Failure to observe
this warning may result in personal injury. Note low or
unequal tyre pressures can make your Scooter become
unstable and reduce battery / motor performance.
To remove a rear wheel from your Scooter for the service of
Motor Brake:
Driving Brake: Warning:
HANDLE BAR BEARINGS
Warning:
TYRE SERVICING REAR WHEEL
Motor Brake:
Driving Brake: Warning:
HANDLE BAR BEARINGS
Warning:
TYRE SERVICING REAR WHEEL
TYRES
Your is designed with 'split' wheel rims.
Do not remove wheel bolts with the wheel inflated. Maintain
pneumatic tyres at 30 p.s.i. (210 kpa). Failure to observe
this warning may result in personal injury. Note low or
unequal tyre pressures can make your Scooter become
unstable and reduce battery / motor performance.
Scooter
(purchased from auto shops).
With the aid of 13mm spanners (not supplied) remove
the four nuts and washers from the rear of the wheel hub.
6. Remove the four wheel bolts and part the hub from the
wheel rims. Part the inner and outer wheel rim from the
side wall of the tyre.
To re-assemble the wheel and hub simply follow the above
procedure in reverse order noting the following points:
1. Make certain you have tightened the two wheel rims to
the centre hub.
2. Make certain your tyre is re-inflated to the recommended
pressure 30 p.s.i. (210 kpa)
3. Make certain that you replace any spacing washers and
keys in the order that they wereremoved.
4. Locking Nut: The special nylon 'locking' centre hub nut
may lose its effectiveness when it has been removed
over a number of times. If the plastic locking ring at the
end of the nut becomes worn or damaged, then the nut
should be replaced with a new part obtained you is your
Agent.
Warning: Please note the rims of your wheel are a split
rim system, do not dismantle the wheel from the hub
without first letting air out of the tyre.