Longshine LCS-8156C1 User Manual
Page 192
A
A - Answer .......................................................................3-35
B
B - CCITT or Bell..............................................................3-58
\B - Transmit Break to Remote ........................................3-67
D
D - Dial .............................................................................3-33
E
E - Command Echo..........................................................3-15
H
H - Disconnect (Hang-Up)................................................3-36
I
I - Identification...................................................................3-7
K
\K - Break Control ............................................................3-68
L
L - Speaker Volume .........................................................3-38
M
M - Speaker Control .........................................................3-38
N
\N - Operating Mode ..........................................................3-6
O
O - Return to On-Line Data Mode....................................3-37
P
P - Set Pulse Dial Default ................................................3-35
Q
Q - Quiet Results Codes Control .....................................3-15
-QCPC - Force Full Startup Procedure Next Connection 3-94
-QCPS - Enable Quick Connect Profile Save ..................3-94
S
S - Read/Write S-Parameter ............................................3-95
S0 - Number of Rings to Auto-Answer.............................3-97
S1 - Ring Counter ............................................................3-97
S10 - Lost Carrier To Hang Up Delay ..............................3-99
S11 - DTMF Tone Duration..............................................3-99
S12 - Escape Prompt Delay (EPD)................................3-100
S14 - General Bit Mapped Options Status.....................3-100
S16 - Test Mode Bit Mapped Options Status ................ 3-100
S17 - Point Of Sale Options Selection .......................... 3-101
S19 - Reserved.............................................................. 3-102
S2 - Escape Character .................................................... 3-97
S20 - Reserved.............................................................. 3-102
S21 - V.24/General Bit Mapped Options Status ............ 3-103
S210 – V.34 Symbol Rates ........................................... 3-113
S22 - Speaker/Results Bit Mapped Options Status....... 3-104
S23 - General Bit Mapped Options Status .................... 3-105
S24 - Sleep Inactivity Timer........................................... 3-105
S25 - Delay To DTR Off ................................................ 3-105
S26 - RTS to CTS Delay ............................................... 3-105
S27 - Bit Mapped Options Status .................................. 3-106
S28 - Bit Mapped Options Status .................................. 3-106
S29 - Flash Dial Modifier Time ...................................... 3-107
S3 - Carriage Return Character....................................... 3-97
S30 - Disconnect Inactivity Timer .................................. 3-107
S31 - Bit Mapped Options Status .................................. 3-107
S36 - LAPM Failure Control .......................................... 3-108
S38 - Delay Before Forced Hang Up............................. 3-108
S39 - Flow Control Bit Mapped Options Status ............. 3-109
S4 - Line Feed Character ................................................ 3-97
S40 - General Bit Mapped Options Status .................... 3-109
S41 - General Bit Mapped Options Status .................... 3-110
S46 - Data Compression Control .................................. 3-110
S48 - V.42 Negotiation Control...................................... 3-110
S5 - Backspace Character............................................... 3-98
S6 - Wait Time before Blind Dialing or for Dial Tone....... 3-98
S7 - Wait Time for Carrier, Silence, or Dial Tone ............ 3-98
S8 - Pause Time For Dial Delay ...................................... 3-99
S86 - Call Failure Reason Code.................................... 3-111
S9 - Carrier Detect Response Time ................................ 3-99
S91 - PSTN Transmit Attenuation Level ....................... 3-112
S95 - Extended Result Codes Control .......................... 3-112
-SCID - Snooping CID (Type II)......................................... 3-4
–SLP= - Set Low Power Mode ........................................ 3-45
–STE= - Set Telephony Extension .................................. 3-46
T
T - Set Tone Dial Default ................................................. 3-35
-TRV – Tip & Ring Voltage .............................................. 3-51
-TTE - Threshold Adjustments for Telephony Extension. 3-52
V
V - Result Code Form...................................................... 3-16
\V - Single Line Connect Message Enable ...................... 3-42
W
W - Connect Message Control ........................................ 3-16
X
X - Extended Result Codes ............................................. 3-17
Z
Z - Soft Reset and Restore Profile .................................... 3-2