Philips AZ114017 - Manual (Page 6)

IMPORTANT SAFETY INSTRUCTIONS
Read before operating equipment_________________________________
REPRODUCTOR DE CD
This product was designed and manufactured to
meet strict quality and safety standards. There
are, however, some installation and operation
precautions which you should be particularly
aware of.
1. Read these instructions - All the safety
and operating instructions should be read
before the appliance is operated.
2. Keep these instructions - The safety and
operating instructions should be retained for
future reference.
3. Heed all warnings - All warnings on the
appliance and in the operating instructions
should be adhered to.
4. Follow all instructions-All operating and
use instructions should be followed.
5. Do not use this apparatus near water -
for example, near a bathtub, washbowl,
kitchen sink, laundry tub, in a wet basement
or near a swimming pool, etc.
6. Clean only with a damp cloth. The
appliance should be cleaned only as
recommended by the manufacturer.
7. Install in accordance with the
manufacturers instructions. Do not block
any of the ventilation openings. For
example, the appliance should not be situated
on a bed, sofa, rug, or similar surface or placed
in a built-in installation, such as a bookcase or
cabinet that may impede the flow of air
through the ventilation openings.
8. Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
9. Do not defeat the
safety purpose of the
polarized or grounding-
type plug. A polarized
plug has two blades with one wider than the
other. A grounding type plug has two blades
and a third grounding prong. The wide blade or
the third prong are provided for your safety.
When the provided plug does not fit into your
outlet, consult an electrician for replacement of
the obsolete outlet.
10. Protect the power cord from being walked
on or pinched particulary at plugs,
convenience receptacles, and the point
where they exit from the apparatus.
11. Only use attachments/accessories
specified by the manufacturer.
Use only with a cart, stand,
tripod, bracket, or table specified by
the manufacturer, or sold with the
apparatus. When a cart is used, use
caution when moving the
cart/apparatus combination to
avoid injury from tip-over.
13. Unplug this apparatus during lightning
storms or when unused for long periods of
time.
14. Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way, such
as power-supply cord or plug is damaged,
liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate
normally, or has been dropped.
EL 4562-E004; 99/3
Modos de reproducción: SHUFFLE y REPEAT
Puede seleccionar y cambiar los diversos modos de reproducción
antes de o durante la misma. Dichos modos pueden combinarse
también con PROGRAM.
SHUFFLE - todas las pistas del CD o del programa se repiten en
orden aleatorio
SHUFFLE y REPEAT ALL - para repetir el CD o el programa completo
de forma continua y en orden aleatorio
REPEAT ALL - para repetir todo el CD o programa
REPEAT - para reproducir la pista actual continuamente
1. Para seleccionar el modo de reproducción, pulse el botón
CD MODE antes o durante la reproducción hasta que la
pantalla muestre la función que desee.
2. Pulse PLAY»PAUSE Hl para inicial la reproducción si está en
la posición STOP.
3. Para volver a la reproducción normal, pulse el botón CD MODE
repetidamente hasta que no se muestre ninguno de los diversos
modos de SFIUFFLE / REPEAT.
- También puede pulsar STOP ■ para cancelar el modo de
reproducción.
Programación de números de pistas
Realice la programación en la posición STOP para seleccionar y
almacenar las pistas del CD en la secuencia deseada. Si lo desea,
puede almacenar cualquier pista más de una vez. Se pueden
guardar en la memoria hasta 20 pistas.
1. Use el botón SEARCH i+< o mh para seleccionar el número de
pista que desee.
2. Pulse PROGRAM
^ Pantalla: aparecerán program y el número de pista
seleccionado. También aparecerá P'"”g brevemente.
-* Si intenta realizar una
programación sin seleccionar en primer lugar un número de
pista, se mostrará 1 ° .
3. Repita los pasos 1 y 2 para seleccionar y almacenar las pistas
que desee.
Si intenta programar más de 20 pistas, se mostrará FULL.
4. Pulse PLAY»PAUSE Hl para iniciar la reproducción del
programa de CD.
Revisión del programa
En la posición de parada, pulse y mantenga pulsado PROGRAM
durante un momento hasta que la pantalla muestre todas las
pistas almacenadas en secuencia.
0 ©