Cata ME 910 - Manual (Page 29)

The turnspit (only available on certain models)
To start the turnspit, proceed as follows:
· Insert the rotisserie rod“A” into the drive unit and groove
“B”into bend“C”;
· Turn the plastiv handle “D” anti clockwise and slide the rack into
the oven runners ensuring that the rod “E” slots into the hole “F”;
· The rotisserie rack must always be fitted in the middle of the
oven (second position from bottom);
· start the turnspit using knob “B” to select setting .
End Cooking Time Knob (I) (only available on certain models)
This model is equipped with a timer to control when the oven
shuts off during cooking. Position of timer knob “I”:Between
10 minutes and 120 minutes.
At the end of the programmed length of time, the timer will
sound and automatically turn off the oven.
5-keys timer procedure baking mode (only available on cer-
tain models)
Settings
After pressing a function button, the required time can be set
via the +/- keys. For quicker regulation, keep the required key
pressed. By pressing the function key and then releasing it,
the pre-selected function appears on the display and remains
for 5 seconds during the time the setting can be performed
(with one hand).Five seconds after releasing the function key
or finishing the setting, the display returns to the clock. Any
program set will start immediately. Program selection is ac-
companied by the surrounding of a buzzer.
Setting the time(clock)
Select the clock function by simultaneously pressing the Du-
ration(2)and End of Cooking (3) time keys and adjust the clock
by means of the +/- 4+5 keys. All the Programs set will be can-
celled and relay will switch off.
Manual operation
Simultaneously press the Duration (2) and End of cooking (3)
time keys (the auto symbol will be cancelled): the saucepan
symbol will light up. Any program set will be cancelled.
Semi automatic operation and cooking duration
Press the Cooking duration (2) key and set the duration by
means of the +/- (4+5) keys. The saucepan symbol will appear.
The relay output will be activated.
If clock=end of the cooking time, the relay and saucepan sym-
bol will be off. The buzzer will sound and symbol A will blink.
Semi automatic operation and end of cooking time
Press the end of cooking time key (3) and set the required time by
means of the +/- (4+5) keys. The symbol A and the symbol of the
saucepan will light up. The relay output will be activated.
If clock=end of the cooking time, the relay and saucepan symbol
will switch off. The buzzer will sound and the symbol A will blink.
Completely automatic operation
Press the duration key (2) and set the required time by means
od the +/- keys(4+5). The symbol A will appear. The relay will
come on the saucepan symbol will appear. Select the End of
cooking time function (3)- the minimum setting time will ap-
pear. Set the required time by means of the +/- keys (4+5).
The relay and the saucepan symbol. The saucepan symbol will re-
appear when the clock time=the calculated switch on time. After
setting the automatic program the symbol A will blink. The buzzer
will sound and the saucepan symbol and relay will switch off.
Minute control
Press the Minute control key (1) and set the required time by
means of the +/- keys (4+5). While the set time runs, the bell
symbol will appear.
When the set time elapses, the buzzer will sound.
Buzzer
The buzzer remains active for 7 minutes after the minute con-
trol cycle or the cooking program has finished
press any function key to stop the buzzer.
Program start-up and check
A set program is run when the required time has also been set.
The remaining timers can be checked at any time by selecting
the relevant function.
Setting error
The setting is not correct if the clock time is between the be-
ginning of the cooking time and the end of the cooking time.
The error is indicated via sounding of a buzzer and blinking of
the Auto symbol.
An incorrect setting can be corrected by re-setting either the
beginning or end of cooking time.
Cancelling a program
A program can be cancelled by selecting the manual function.
A set program is automatically cancelled when it reaches the
end of its cycle.
The oven light
Set knob “B”to the
symbol to turn it on .It lights the oven
and stays on when any of the electrical heating elements in
the oven come on.
F
E
A
C B
D