Document Outline

• Vipersat
• CDD-56X Series
• CDD-562L, CDD-564/564L
• Satellite Network Demodulator Router
  • General
    • How to Use This Manual
      • Manual Organization
        • Chapter 1 — General
        • Chapter 2 — Quick Start Configuration
        • Chapter 3 — Using the Command Line Interface (CLI)
        • Appendix A — Network Addressing
        • Appendix B — Automatic Switching
        • Appendix C — Dynamic Power Control
        • Appendix D — ECM Migration
        • Appendix E — Glossary
      • Conventions and References
    • Product Description
      • Introduction
      • Demodulator Features
      • Router Features
      • Network and Bandwidth Management
      • Dynamic SCPC (dSCPC)
      • STDMA
      • Single Hop On Demand
      • Turbo Product Coding
      • Header Decompression
      • Payload Decompression
      • Data Decryption
      • New in This Release
        • 1.6.11/2.6.11 Release
          • Dynamic Entry Channel Mode
    • Customer Support
      • Contact Information
      • Return Material Authorization
      • Reader Comments / Corrections
  • Quick Start Configuration
    • Introduction
    • Initial Configuration
      • Terminal Connection
      • Network Role
      • Setting Vipersat CDD-56X Operating Parameters
        • Set the Feature Configuration
        • Set the IP Address
        • Configure the Route Table
          • Routing in a Vipersat Network
          • Creating the Routes
        • Set the Satellite Demod Configuration
        • Set the Vipersat Configuration
  • Using the Command Line Interface (CLI)
    • General
      • Common Screen Commands
        • Demod Select
        • Save Parameters to Permanent Storage
        • Exit
        • Telnet Logout
    • Menu Descriptions
      • Main Menu
        • Administration
      • Feature Configuration
        • Vipersat Feature Codes
        • Vipersat Management
        • Vipersat STDMA
        • Vipersat Auto Switching
        • Vipersat File Streamer
    • Vipersat Configuration
      • STDMA Mode
        • STDMA
        • STDMA Tx Rate
        • Hub Type
          • 1 – Fixed
          • 2 – Dynamic Slot
          • 3 – Dynamic Cycle
          • 4 – GIR
          • 5 – Entry Channel
          • 6 – ECMv2
        • ECMv2 Mode
        • Group ID
        • STDMA Max Power Hunt
        • Low Data Rate Fast Acquisition
        • Burstmap Multicast IP
        • Outbound IP
        • Cycles Per Burst Map
        • Slot Guardband
        • Slot Preamble Length
        • Slot Data Length
        • Nominal Data Length
        • Maximum Data Length
        • Minimum Data Length
        • Total Slot Count
        • Slot Cycle Length
        • Slot Start in Cycle
        • Set Remotes
          • Adding a Remote to the STDMA Group
          • Base
          • Remote Count
          • Set Remote Policies
          • Delete Remote
          • Enable/Disable Remote
          • View Remote(s)
          • Remove Timeout
          • Remove Retry Timeout
        • LNB LO Frequency
        • Satellite Frequency Conversion
        • STDMA Statistics
          • Stats Accumulation Window
          • Clear
        • Show Hub Statistics
      • STDMA/SCPC Automatic Switching
        • Auto Switching
        • Current WAN Transmit Mode
        • Load Switching
        • STDMA Slot Capacity
        • STDMA Switch Delay
        • Percent Allocation
        • Keep Alive Timer for Carrier Inhibit
        • Hitless Switching Parameters
          • Delay for Mod
          • Delay for Demod
          • LockTimes
          • Apply Delay Values
        • SOTM Update
      • Unit Role
      • Expansion Unit
      • Network ID
      • Unit Name
      • Receive Multicast Address
      • Managing IP Address
      • Management Security
      • Primary Heart Beat
      • Home State Revert
      • Dynamic Power Control Configuration
        • DPC Enabled
        • Speed Up EbNo
        • Target DPC Address
      • Set Home State Parameters
        • Set Current Configuration as Home State
        • Force Modem to Home State
        • STDMA State
        • Receive Frequency
        • Receive Data Rate
        • Receive FEC Type
        • Receive Coding Rate
        • Receive Modulation Type
      • Vipersat Summary
      • Vipersat Migration
      • UDP Port Base Address
      • Alerts
  • Network Addressing
    • Introduction
    • The OSI Reference Model
      • Layers 1 – 3
    • Binary Math
    • IP Addressing
      • IP Address Classes
        • Class A
        • Class B
        • Class C
        • Class D
        • Class E
        • Private Network IP Addresses
        • Network Address Translation (NAT)
      • Subnets
      • Subnet Mask
      • Network Segments
      • Default Gateways
      • MAC Addresses
  • Automatic Switching
    • General
      • Hitless Switching
    • Load Switching
      • Overview
        • Bandwidth Allocation and Load Switching by the Hub STDMA Burst Controller
      • Load Switching—STDMA Hub
        • Hub Switching Parameters
        • Hub Switching Process
      • Load Switching—Remote
        • Remote Switching Parameters
        • Determination for Switching
      • Load Switch Example
        • Reduced Data Flow in Switched Mode (SCPC)
    • Application Switching
    • ToS Switching
      • ToS Background
        • Detection of ToS Stamped Packets
        • Configuration
      • Example Implementations
        • ToS Switching Per Device
        • ToS Switching Per Traffic Type
        • ToS Remarking
        • ToS to DSCP Value Conversions
        • Mesh Setup Based on ToS Detection
    • Entry Channel Mode Switching
      • STDMA Entry Channel Mode
        • Fail-Safe Operation
        • Using STDMA ECM
          • Switching an ECM Remote from SCPC to STDMA
      • Dynamic Entry Channel Mode
        • Hub Configuration
        • Remote Configuration
        • ECM Processing
  • Dynamic Power Control
    • Introduction
    • Description
      • BER Waterfall Mapping
      • Delta Power Compensation
      • Theory of Operation
    • Configuration
      • Main DPC Menu
        • Enable DPC
        • Target Eb/No
        • Speed Up Eb/No Range
        • Target DPC (IP) Address
      • Calculate Max Power Menu
        • Calibrated Data Rate
        • DPC Margin
        • Nominal Power Level
        • Max Data Rate
        • Max Code Rate
        • Max Modulation
        • Max FEC Type
        • Calculate Max Power
        • Max Power
    • Signal Power Level Considerations
      • Power Considerations
      • Cabling Considerations
  • ECM Migration
    • General
    • Migration Procedure
      • Configure Remote Units
      • Configure Hub Unit
  • Glossary