Chapter 2 - hardware installation, System board layout, System memory – DFI HD632-H81 User Manual
Page 9: Chapter 2 chapter 2 - hardware installation, Board layout, Rear i/o onboard i/o storage expansion, Chapter 2 hardware installation, Supports
www.dfi .com
9
Chapter 2 Hardware Installation
Chapter 2
Chapter 2 - Hardware Installation
Board Layout
PCIe x16
PCIe x4
1
2
10 9
1
2
10 9
1
2
10 9
1
2
10 9
1
2
10
9 1
2
10
9
1
2
10
9 1
2
10
9
Buzzer
1
System_Fan 2
Socket LGA1150
Nuvoton
NCT6106D
Power-on
Select (JP10)
1
1
ASMedia
ASM1442
1
2
9
10
PCI 1
PCI 2
PCI 3
PCI 4
PCI 5
1
1
USB 4-5
Power Select
(JP6)
Line-in
Line-out
Mic-in
LAN 2
USB 4-5
USB 2.0
LAN 1
USB 0-1
COM2
COM1
VGA
DVI-D
PS/2 KB/MS
USB 8-9
USB 2.0
TPM (optional)
1 2
Front
Panel
11 12
ASMedia
ASM1182
USB 0-1
Power Select
(JP5)
PS/2 KB/MS
Power Select
(JP1)
COM1 RS232/Power
Select (JP15)
COM2 RS232/Power
Select (JP14)
USB 8-9 Power
Select (JP4)
Standby
Power LED
Chassis
intrusion
1
1
2
25
26
Nuvoton
NCT5104D
1
4
1
2
11
12
COM3 RS422/485
Select (JP2)
Battery
Realtek
ALC886
2
9
10
1
Front
Audio
S/PDIF
1
DIO
1
2
19
System_Fan 1
1
CPU Fan
1
12 24
ATX
Power
1 13
+12V
Power
1 5
4 8
COM 6 COM 5
COM 4 COM 3
SATA 0
1
SATA 1
1
SATA 4
1
SATA 5
1
COM 7
COM 8
COM 9
COM 10
SPI Flash
BIOS
2
1
6
5
2
1
6
5
1
1
SATA DOM
Power Select
(JP11)
USB 2-3 Power
Select (JP8)
DDR3_1 DDR3_2
1
2
3
4
Intel
WGI210AT
Intel
WGI210AT
1
Clear CMOS
Data (JP9)
Parallel
1
1
7
8
2
SPI
JTAG
SATA 3.0
SATA 2.0
Note:
SATA5 supports SATA DOM.
USB 10
USB 2-3
LPC Debug
USB 3.0
Intel
H81
USB
2.0
ASMedia
ASM1085
1
1
1
DIO Power Select
(JP13)
DIO 11/13/15/17
Output State (JP7)
DIO 3/5/7/9
Output State (JP12)
(JP7)
(JP12)
(JP13)
System Memory
Standby
Power LED
Features
Important:
Electrostatic discharge (ESD) can damage your board, processor, disk drives, add-in
boards, and other components. Perform installation procedures at an ESD workstation
only. If such a station is not available, you can provide some ESD protection by wear-
ing an antistatic wrist strap and attaching it to a metal part of the system chassis. If
a wrist strap is unavailable, establish and maintain contact with the system chassis
throughout any procedures requiring ESD protection.
Important:
When the Standby Power LED lit red, it indicates that there is power on the system
board. Power-off the PC then unplug the power cord prior to installing any devices.
Failure to do so will cause severe damage to the motherboard and components.
Rear I/O
Onboard I/O
Storage
Expansion
DDR3-2
DDR3-1
• Two
240-pin
DDR3 DIMM sockets
• Supports
DDR3 1066/1333/1600MHz
•
Supports dual channel memory interface
•
Supports up to 16GB system memory