Marantz UD9004 - Manual (Page 53)

49
Troubl
eshooting
Information
Pl
ayback
Setup
Connections
Getting Started
Specifications
ENGLISH
Pl
ayback
Operations Enabled During Playback
During playback of a BD or DVD-Video recorded with several
camera angles, you can change the angle.
Switching the Angle
BD DVD-V
NOTE
Angle changing may be restricted, depending on the disc.
1 Press ANGLE button during playback.
The angle number currently being played is displayed.
Angle
1/3
2
Use d, f buttons to select angle.
Angle
2/3
3 Press ANGLE button.
The setup screen disappears.
Press DIMMER button.
The display brightness each time the button is
pressed.
Normal Dim Dark Off
Changing the Brightness of the
Display (Dimmer Control)
Even when “Off” is selected, the status of operations that are
performed appears momentarily on the display if “Display Setup”
– “Temporary Display” on the GUI menu is set to “On” (vpage 32).
When you make an HDMI connection with a TV or AV Amp compatible
with UD9004 and HDMI control functions, you can perform the
following operations by setting the HDMI control function of each
device.
TV or AV Amp power is turned on by operating n
the UD9004, and functions change with UD9004
input.
Turning off the TV’s power turns the UD9004’s n
power to standby.
Operating the UD9004 via the TV’s remote n
control.
(When the TV’s remote control has player operation buttons)
If the HDMI control function does not operate properly, check the
following points.
Is the TV or AV Amp compatible with the HDMI control function? •
Is the setting of the UD9004’s HDMI output terminal correct? (Step •
1)
Are the HDMI control function settings of all equipment correct?
•
(Step 3)
After setting, did you add another HDMI device connection or
•
make any changes in the connections? In this case, perform setting
again.
HDMI Control Function
NOTE
The HDMI control function controls operations of a TV that is •
compatible with the HDMI control function. Make sure that the TV
and HDMI are connected when you perform HDMI control.
Some functions may not operate depending on the connected TV
•
or AV Amp. Check the owner’s manual of each device for details
beforehand.
When “Other Setup” – “Power Saving” on the GUI menu is set
•
to “Power Saving Standby” or “Normal Standby” (vpage 32),
the player’s power cannot be turned on using the HDMI control
function.
When “HDMI Setup” – “HDMI Control” – “Power Off Control” on
•
the GUI menu is set to “Off” (vpage 26), the UD9004 is not set to
standby even if the connected device is in the standby mode.
1 Set the HDMI output terminal corresponding with
the HDMI control function.
On the GUI menu, set “HDMI Setup” – “HDMI Control” (vpage
26).
The HDMI control function will work only on one of the 2 HDMI b
output terminals on the UD9004.
2 Turn the power on for all the equipment connected by
HDMI cable.
3 Set the HDMI control function for all equipment
connected by HDMI cable.
On the GUI menu, set the UD9004 with “HDMI Setup” – “HDMI
Control” (vpage 26).
Please refer to the owner’s manual as regards setting of connected b
devices.
Carry out Steps 2 and 3 should any of the equipment be
b
unplugged.
4 To ensure that the UD9004’s HDMI video output is
projected on the TV screen, change the input function
of the TV and AV Amp.
5 When you turn the TV’s power to standby, check that
the power of the UD9004 and AV Amp also goes on
standby.
HDMI
Control
Function