Teac DM-24 Quick Start - Manual (Page 15)

15
DM-24 Quick Start Guide
1. All channel EQ set to ON. Hi =10.1kHz, H.
SHELF, Gain =0dB, Hi Mid=5.04kHz, Q=1.20,
Gain =0dB, Low Mid=1.26kHz, Q=1.20,
Gain=0dB, Low=125Hz, L. SHELF, Gain=0dB.
2. All channel dynamics set to OFF.
3. Compressor settings:Threshold=-10dB,
Ration=4.00:1, Attack=53ms, Release=180ms.
4. Channels 1- 24 set to zero, 25-32 set to unity,
buss masters, aux masters and stereo buss set to
unity gain.
5. All pans set to center.
6. All channels assigned to the stereo buss.
7. Channels 1-8 should reference TDIF-1,
9-16 TDIF-2, 17-24 TDIF-3.
8. Channels 1-24 should be set to TDIF returns.
9. Channels 25-28 should be set to Effect 1 L&R
and Effect 2 L&R.
10. Channels 29-32 should be set to assignable
returns 1-4.
11. Channels 25-32 should be linked stereo pairs.
12. TDIF-1=Direct out1-8/Buss 1-8, TDIF-2=Direct
out 9-16/Bus 1-8, TDIF-3=Direct out 1-8/Buss
1-8.
13. Aux 1-6 source set to Post.
14. Aux 1-6 levels set to zero.
15. Digital stereo outputs set to 16 bit noise shaped.
16. Digital out 1 set to AES/EBU, Digital out 2 set
to S/PDIF.
17. Digital out 1and 2 reference the stereo buss .
18. Format of digital input 1-2 can be recognized
automatically.
19. All TDIF I/O set to 24 bit.
20. Assignable sends and returns all set to sends and
returns(not inserts.)
21. Insert matrix compressors should be set to
stereo buss only.
22. Effect 1 set to MONO input-Left input source
AUX 1
23. Effect 2 set to MONO input-Left input source
AUX 2
1. All channel EQ set to ON. Hi =10.1kHz, H.
SHELF, Gain =0dB, Hi Mid=5.04kHz, Q=1.20,
Gain =0dB, Low Mid=1.26kHz, Q=1.20,
Gain=0dB, Low=125Hz, L. SHELF, Gain=0dB.
2. All channel dynamics set to OFF.
3. Compressor settings:Threshold=-10dB,
Ration=4.00:1, Attack=53ms, Release=180ms.
4. Channels 1- 24, buss masters, aux masters set to
unity gain.
5. Channels 25-32 set to zero.
6. All pans set to center.
7. NO channel assignments (stereo, buss 1-8,
direct out.)
8. Channels 1-8 should reference TDIF-1, 9-16
TDIF-2, 17-24 TDIF-3.
9. Channels 1-16 should be set to Mic/line inputs.
10. Channels 17-24 should be set to TDIF returns.
11. Channels 25-28 should be set to Effect 1 L&R
and Effect 2 L&R.
12. Channels 29-32 should be set to assignable
returns 1-4.
13. Channels 25-32 should be linked stereo pairs
14. TDIF-1=Direct out1-8/Buss 1-8, TDIF-2=Direct
out 9-16/Bus 1-8, TDIF-3=Direct out 1-8/Buss
1-8.
15. Aux sends should be set to fader control.
16. Aux 1-2 should be linked.
17. Aux 1-2 source should be set to Return for
channels 1-16.
18. Aux 1-2 source should be set to Pre for channels
17-32
19. Aux 1-2 levels should be set to unity gain for
channels 1-24.
20. Aux 3-6 source should be set to Pre.
21. Aux 3-6 levels should be set to zero.
22. Digital stereo outputs set to 16 bit noise shaped.
23. Digital out 1 set to AES/EBU, Digital out 2 set
to S/PDIF.
24. Digital out 1and 2 reference the stereo buss.
25. Format of digital input 1-2 can be recognized
automatically.
26. All TDIF I/O set to 24 bit.
27. Assignable sends and returns all set to sends and
returns(not inserts.)
28. Insert matrix compressors should be set to
busses 1-6.
Mixing Snap Shot
Recording Snap Shot